Projects / Bass and treble tone control

Bass and treble tone control

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. TL072

    Build the op-amp stage

    Unity gain with the supply decoupled.

  2. Add the bass network

    Pot and 47 nF capacitors.

  3. Add the treble network

    Pot and 10 nF capacitors.

  4. Test at the centre

    Flat response.

  5. Sweep the frequency

    Note the gain at 20 Hz, 1 kHz and 20 kHz.

  6. Move each pot

    Plot boost and cut.

  7. TL072

    Use it before an amplifier

    Listen to music.

In short

How do you build a bass and treble tone control?

A Baxandall tone stack with an op-amp lets you boost or cut bass and treble. You need TL072 dual JFET op-amp, Potentiometer 10 kΩ × 2, Resistor 10 kΩ × 4, Ceramic capacitor 10 nF × 2, Ceramic capacitor 47 nF × 2, Dual-rail ±12 V DC-DC module and Breadboard 830 Tie Points. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Dual-rail moduleTL072 pin 8 (+) and pin 4 (-)Plus and minus supply
Input10 kΩ, then inverting input pin 2Input
Non-inverting pin 3GroundReference
Bass potIn the feedback with 47 nF capacitorsBass control
Treble potIn the network with 10 nF capacitorsTreble control
Output pin 1Feedback network, and outOutput

No code needed

A Baxandall network changes the balance between low and high frequencies. The bass pot with larger capacitors controls tone below about 300 Hz, and the treble pot with smaller capacitors controls tone above about 3 kHz; centre both pots for a flat response. Placing the network in the op-amp's feedback loop gives boost as well as cut. Use a dual-rail supply of plus and minus 12 V from the small module, and check the module's output before connecting the op-amp. Sweep a sine wave from 20 Hz to 20 kHz with a phone generator app and a meter or oscilloscope, and plot the gain at five pot positions. Use it in front of an amplifier, not after the volume control, to avoid clipping.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Both pots centredAbout flat from 20 Hz to 20 kHz
Bass upMore gain below 300 Hz
Treble downLess gain above 3 kHz
SupplyPlus and minus 12 V, no hum

If it does not work

Hum

Keep leads short and use a decent supply.

Distortion

Lower the input level.

No effect

Check the pots are in the feedback path.

Hiss

Use shorter, shielded leads.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the bass and treble tone control?

TL072 dual JFET op-amp, Potentiometer 10 kΩ × 2, Resistor 10 kΩ × 4, Ceramic capacitor 10 nF × 2, Ceramic capacitor 47 nF × 2, Dual-rail ±12 V DC-DC module and Breadboard 830 Tie Points.

How long does the bass and treble tone control take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the bass and treble tone control works?

Both pots centred: About flat from 20 Hz to 20 kHz. Bass up: More gain below 300 Hz. Treble down: Less gain above 3 kHz.

Hum: what should I check?

Keep leads short and use a decent supply.

Distortion: what should I check?

Lower the input level.

No effect: what should I check?

Check the pots are in the feedback path.

Hiss: what should I check?

Use shorter, shielded leads.