Projects / Two-tone siren box

Two-tone siren box

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. Wire the power

    Pins 14 and 7, bypass capacitor, resets high.

  2. NE556

    Wire the slow timer

    Two 100k and the 10 uF on pins 1, 2 and 6.

  3. NE556

    Wire the tone timer

    Two 10k and the 100 nF on pins 13, 12 and 8.

  4. NE556

    Link the timers

    10k from pin 5 to pin 11.

  5. Wire the speaker

    Pin 9 through 10 uF and 220 ohm to the speaker.

  6. Power it up

    The siren starts warbling.

  7. Measure the two pitches

    About 480 Hz and 665 Hz.

  8. Change the warble

    Try a different slow capacitor.

In short

How do you build a two-tone siren box?

Both halves of a dual timer run, one as a slow switch and one as the tone, giving a siren that warbles between two pitches. You need NE556 dual timer, Resistor 10 kΩ × 3, Resistor 100 kΩ × 2, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 10 µF × 2, Resistor 220 Ω, Speaker 8 Ω 0.5 W, 5 V 2 A USB adapter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5 V adapter positiveRed railSupply
5 V adapter negativeBlue railGround
NE556 pin 14 (VCC) and pin 7 (GND)Red rail and blue railPower
100 nF capacitorPin 14 to pin 7Supply bypass, close to the chip
Pins 4 and 10 (resets)Red railResets held high
Slow timer: 100k from red rail to pin 1, 100k from pin 1 to pins 2 and 610 uF from pins 2 and 6 to GND (plus toward pin 2)Slow timer, about 0.5 Hz
Slow timer output pin 510 kilohm to pin 11Shifts the tone timer control voltage
Tone timer: 10k from red rail to pin 13, 10k from pin 13 to pins 12 and 8100 nF from pins 12 and 8 to GNDTone timer, about 500 to 700 Hz
Tone timer output pin 910 uF (plus toward pin 9) then 220 ohm to the speakerCoupling capacitor and current limit
Speaker other legBlue railReturn

Code

The NE556 puts two 555 timers in one chip, which is exactly what a siren needs: one timer decides how fast the pitch switches, and the other makes the tone. The slow half is a normal astable oscillator with a 10 microfarad capacitor, switching its output high and low about every second. The tone half is another astable using 10 kilohm resistors and 100 nanofarads, which on its own gives about 480 hertz. The trick that makes the siren is the control pin. Every 555 has an internal reference at two thirds of the supply that sets where it flips, and that point is brought out as the control pin. If the slow timer pulls that pin down through a resistor, the thresholds move closer together and the tone speeds up to about 665 hertz, so the pitch changes between two notes as the slow timer swings. The speaker connects through a 10 microfarad capacitor and 220 ohms, so it never sees DC and the chip is not asked for more than a small current. Try changing the slow capacitor to change the warble speed, or the 10 kilohm coupling resistor to change how far the pitch jumps. Keep the supply at 5 volts, and keep the speaker volume modest, because a siren is meant to be loud and can be tiring close to your ears.

Build notes (no code needed for this build)

NE556 pins: 1 DISCH1, 2 THRESH1, 3 CONT1, 4 RESET1, 5 OUT1, 6 TRIG1, 7 GND, 8 TRIG2, 9 OUT2, 10 RESET2, 11 CONT2, 12 THRESH2, 13 DISCH2, 14 VCC.

Slow timer (first half), astable: R1 = 100k, R2 = 100k, C = 10 uF.
  Period = 0.693 x (R1 + 2 x R2) x C = 0.693 x 300k x 10 uF = about 2.1 s, so the pitch changes about twice every 2 seconds.

Tone timer (second half), astable: R1 = 10k, R2 = 10k, C = 100 nF.
  With the control pin left alone: frequency = 1.44 / ((R1 + 2 x R2) x C) = 1.44 / (30k x 100 nF) = about 480 Hz.

Warble: the 10 kilohm resistor from pin 5 to pin 11 pulls the control voltage of the tone timer. When the slow output is high the control voltage stays near 3.3 V, so the tone is about 480 Hz.
When the slow output is low it pulls pin 11 down to about 2.5 V, the thresholds move closer together, and the tone rises to about 665 Hz (calculated for a 5 V supply).

Speaker: the 10 uF capacitor blocks DC, and the 220 ohm resistor limits the speaker current to about 15 mA. Keep the speaker away from your ears.
Real frequencies move with the capacitor tolerance, so measure with a phone tuner app or a scope if you can.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onA warbling tone within a second
Two pitchesAbout 480 Hz and 665 Hz
Change rateAbout once a second
Remove the coupling resistorA single steady tone
Smaller slow capacitorFaster warble

If it does not work

No sound

Check power on pins 14 and 7 and the speaker wires.

Steady tone only

Check the 10k from pin 5 to pin 11.

No tone at all

Check the resets are on 5 V.

Very quiet

Check the polarity of the coupling capacitor.

Clicks only

Check the tone timing parts on pins 8, 12 and 13.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the two-tone siren box?

NE556 dual timer, Resistor 10 kΩ × 3, Resistor 100 kΩ × 2, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 10 µF × 2, Resistor 220 Ω, Speaker 8 Ω 0.5 W, 5 V 2 A USB adapter, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the two-tone siren box take to build?

About 90 minutes for a beginner maker, in 8 steps.

How do I know the two-tone siren box works?

Power on: A warbling tone within a second. Two pitches: About 480 Hz and 665 Hz. Change rate: About once a second.

No sound: what should I check?

Check power on pins 14 and 7 and the speaker wires.

Steady tone only: what should I check?

Check the 10k from pin 5 to pin 11.

No tone at all: what should I check?

Check the resets are on 5 V.

Very quiet: what should I check?

Check the polarity of the coupling capacitor.