Projects / Analog multiplexer data selector

Analog multiplexer data selector

Intermediate1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. UNO

    Power the chip

    Wire 5 V, ground, VEE and the inhibit pin.

  2. UNO388 lux

    Wire the eight inputs

    Four pots, two LDR dividers, a half-supply and a ground.

  3. UNO

    Set the address by hand

    Use the DIP switches and read the meter.

  4. UNO

    Step through the eight channels

    Note the changes on each.

  5. UNO

    Move to the Uno

    Connect A, B, C and COM to the Uno and upload.

  6. UNO391 lux

    Watch eight values

    Turn the pots and cover the LDRs.

  7. UNO

    Check the references

    Channel 6 should read about 512 and channel 7 near 0.

In short

How do you build an analog multiplexer data selector?

A CD4051 selects one of eight sensors to send to a single meter, picked by three address lines. You need CD4051 analog multiplexer, DIP switch 8-position, Potentiometer 10 kΩ × 4, LDR Photoresistor × 2, Resistor 10 kΩ × 5, Digital multimeter, Arduino Uno R3, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 60 minutes.

Level
Intermediate
Time
About 60 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
CD4051 pin 16 (VDD)5VPower
CD4051 pin 8 (VSS) and pin 7 (VEE)GNDGround and negative supply
CD4051 pin 6 (INH)GNDChip enabled
CD4051 pin 11 (A)DIP switch 1, with 10 kΩ to GND, or Uno D2Address bit 0
CD4051 pin 10 (B)DIP switch 2, with 10 kΩ to GND, or Uno D3Address bit 1
CD4051 pin 9 (C)DIP switch 3, with 10 kΩ to GND, or Uno D4Address bit 2
DIP switch other sides5VA closed switch reads high
Potentiometer wipers (four)CD4051 pins 13, 14, 15, 12 (channels 0 to 3)Four input signals, pot ends on 5V and GND
LDR with 10 kΩ5V through the LDR, 10 kΩ to GND, midpoint to pin 1 (channel 4)Light sensor
Second LDR with 10 kΩSame, midpoint to pin 5 (channel 5)Light sensor
Pin 2 (channel 6)5V through 10 kΩ and GND through 10 kΩHalf supply reference
Pin 4 (channel 7)GNDZero reference
CD4051 pin 3 (COM)Multimeter + or Uno A0Selected signal out

Code

The CD4051 connects one of eight inputs to a single common pin according to the three-bit address on A, B and C (channel number = A + 2B + 4C). With the supply at 5 V and VEE at ground, signals must stay between 0 and 5 V. The switch has some on-resistance, so read into a high-impedance input such as a multimeter or an Arduino analogue pin. With the DIP switches, set the address by hand and read the meter; with the Uno, disconnect the switches and drive the address lines from D2 to D4. The pin numbers on the table follow the standard CD4051 pinout: 13, 14, 15, 12, 1, 5, 2, 4 are channels 0 to 7. Arduino IDE, board "Arduino Uno" (or "Arduino Nano" with processor ATmega328P).

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Reads all eight channels through the CD4051 with address lines on D2, D3 and D4.
const byte ADDR[3] = {2, 3, 4};   // A, B, C
const byte COM = A0;

int readChannel(byte ch) {
  for (byte i = 0; i < 3; i++) digitalWrite(ADDR[i], (ch >> i) & 1);
  delayMicroseconds(100);          // let the switch and the input settle
  analogRead(COM);                 // throw away the first reading after switching
  return analogRead(COM);
}

void setup() {
  for (byte i = 0; i < 3; i++) pinMode(ADDR[i], OUTPUT);
  Serial.begin(9600);
}

void loop() {
  for (byte ch = 0; ch < 8; ch++) {
    Serial.print(readChannel(ch));
    Serial.print(ch < 7 ? "\t" : "\n");
  }
  delay(500);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

513	512	512	512	512	511	511	511
512	511	512	513	512	513	512	512
511	512	512	512	512	512	512	511
513	512	513	513	511	512	512	512
512	511	512	511	512	513	513	512
511	512	512	512	512	511	513	512

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Address 000Channel 0, pot 1
Address 111Channel 7, near zero
Covering an LDRIts channel changes
Channel 6About half scale

If it does not work

All channels read the same

Check the address lines and the inhibit pin.

Readings are noisy

Add a 100 nF capacitor on COM to ground.

Channel numbers wrong

Check the pin order against the datasheet.

Signal clipped

Keep inputs between 0 and 5 V.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the analog multiplexer data selector?

CD4051 analog multiplexer, DIP switch 8-position, Potentiometer 10 kΩ × 4, LDR Photoresistor × 2, Resistor 10 kΩ × 5, Digital multimeter, Arduino Uno R3, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the analog multiplexer data selector take to build?

About 60 minutes for a intermediate maker, in 7 steps.

How do I know the analog multiplexer data selector works?

Address 000: Channel 0, pot 1. Address 111: Channel 7, near zero. Covering an LDR: Its channel changes.

All channels read the same: what should I check?

Check the address lines and the inhibit pin.

Readings are noisy: what should I check?

Add a 100 nF capacitor on COM to ground.

Channel numbers wrong: what should I check?

Check the pin order against the datasheet.

Signal clipped: what should I check?

Keep inputs between 0 and 5 V.