Build it step by step
0 of 8 doneLearn the dial
Find DC volts, ohms, mA, continuity and diode.
Measure the battery
Meter across the battery in DC volts.
Measure each resistor
Out of the circuit, ohms range.
Join resistors
Measure the series and parallel combinations.
Build the divider
Measure the voltage across the 100 kilohm.
Measure the current
Meter in series on the mA range.
Restore the leads
Red lead back to the voltage jack.
Check continuity and the diode
Beeper and diode ranges.
How do you build a ten multimeter measurements?
A practice sheet for voltage, resistance, current, continuity and a diode check on a small breadboard with a 9 V battery. You need Digital multimeter (auto-range, true RMS), Resistor 1 kΩ, Resistor 10 kΩ, Resistor 100 kΩ, Signal Diode 1N4148, 9 V battery, 9 V battery snap with DC jack, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 90 minutes.
- Level
- Beginner
- Time
- About 90 min
- Parts
- 9
Parts list
- Tools & InstrumentsBuy
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuyResistor 100 kΩ × 1
- SemiconductorsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery snap positive | Breadboard red rail | Positive rail |
| 9 V battery snap negative | Breadboard blue rail | Ground rail |
| 10 kilohm resistor | Red rail to a free row | Used for current and divider tests |
| 100 kilohm resistor | That row to the blue rail | Lower part of the divider |
| Multimeter black lead | COM jack | Always stays here |
| Multimeter red lead | VΩ jack, or the mA jack for current | Move it for the current test and back after |
| 1N4148 diode | On the board with the banded end as the cathode | For the diode test |
Code
A multimeter is the first measuring tool in electronics, and most mistakes with it come from using the wrong range or putting the leads in the wrong jacks. This practice sheet walks through ten measurements on a simple breadboard with a 9 volt battery, so you learn the dial and build the habit of predicting a reading before you take it. Voltage is measured across a part, with the meter in parallel, and it hardly disturbs the circuit. Resistance is measured with the part out of the circuit and unpowered, and a resistor in parallel with another part reads lower than it should, so lift one leg if you are unsure. Current is the one that catches people: the meter must be placed in series, so the circuit has to be opened and the meter put in the gap, and the current range has almost no resistance, so connecting it across a battery acts like a short circuit and can blow the meter fuse. After a current test, always return the red lead to the voltage jack. The last two measurements, continuity and the diode test, show why the meter has a beeper and why a diode reads about half a volt one way and open the other way. Compare each reading with the calculated value and expect small differences from the resistor tolerance and the battery state.
Build notes (no code needed for this build) Rules before you start: - Use only the 9 V battery and the parts in the list. Never measure mains with this meter practice. - Current is measured IN SERIES with the circuit, on the mA range, with the red lead in the mA jack. - After a current measurement, put the red lead back in the VΩ jack before measuring voltage. - Measure resistance only on parts that are not connected to power. The ten measurements and what to expect: 1. Battery voltage (DC V): a new 9 V battery reads about 9.3 to 9.6 V. 2. 1 kilohm resistor (ohms): about 1.00 kilohm, within the tolerance band (a 5 percent part reads 0.95 to 1.05 kilohm). 3. 10 kilohm resistor: about 10 kilohm. 4. 100 kilohm resistor: about 100 kilohm. 5. 10 kilohm and 100 kilohm in series (ohms): about 110 kilohm. 6. 1 kilohm and 10 kilohm in parallel (ohms): about 0.91 kilohm, lower than the smaller resistor. 7. Divider voltage: battery across the 10 kilohm and 100 kilohm in series, measure across the 100 kilohm: about 8.2 V. 8. Series current: battery, 10 kilohm, meter on mA range, back to the battery: about 0.9 mA (9 V divided by 10 kilohm). 9. Continuity: jumper wire gives a beep and a reading near 0 ohm, two separated rows give no beep. 10. Diode test: red lead on the anode, black on the banded end shows about 0.5 to 0.7 V; reversed shows OL. Record each reading next to the expected value and write one sentence on any difference.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Battery | About 9.3 to 9.6 V when new |
| Series 10k and 100k | About 110 kilohm |
| Parallel 1k and 10k | About 0.91 kilohm |
| Series current through 10k | About 0.9 mA |
| Diode forward and reverse | About 0.5 to 0.7 V and OL |
If it does not work
Meter shows 0 for current
The fuse may be blown, or the lead is in the wrong jack.
Resistance reads too low
The part is still in the circuit or in parallel with another.
Voltage reading is zero
Check the red lead is back in the voltage jack.
OL on resistance
The part is open or the range is too low.
Diode reads OL both ways
Swap the leads to find the direction.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the ten multimeter measurements?
Digital multimeter (auto-range, true RMS), Resistor 1 kΩ, Resistor 10 kΩ, Resistor 100 kΩ, Signal Diode 1N4148, 9 V battery, 9 V battery snap with DC jack, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.
How long does the ten multimeter measurements take to build?
About 90 minutes for a beginner maker, in 8 steps.
How do I know the ten multimeter measurements works?
Battery: About 9.3 to 9.6 V when new. Series 10k and 100k: About 110 kilohm. Parallel 1k and 10k: About 0.91 kilohm.
Meter shows 0 for current: what should I check?
The fuse may be blown, or the lead is in the wrong jack.
Resistance reads too low: what should I check?
The part is still in the circuit or in parallel with another.
Voltage reading is zero: what should I check?
Check the red lead is back in the voltage jack.
OL on resistance: what should I check?
The part is open or the range is too low.
