Projects / Four sensors on one I²C bus

Four sensors on one I²C bus

Intermediate1.2 hGuided buildReviewed
ESP32 DevKitGPIO21GPIO223V3GNDBME280 0x76INA219 0x40MPU6050 0x68BME280 0x7626 C 12 mAnext page in 2 sOLED 0x3C
Found 0x3C, 0x40, 0x68, 0x76

Tap a part to see what it does.

Tap the parts to see what each one does. A teaching simulation, not a circuit simulator.

Build it step by step

0 of 4 done
  1. ESP32

    Make an I2C rail

    Use one breadboard row for SDA and one for SCL so every module plugs into the same lines.

  2. ESP32

    Add the modules one by one

    Plug in one module, upload the scanner, check its address, then add the next.

  3. ESP32INA2190.28 A

    Wire the INA219 load

    Put the INA219 in series with a small LED load so it has some current to read.

  4. ESP329.2 mASSD1306

    Upload the dashboard

    The OLED shows a new page every 2 seconds.

In short

How do you build a four sensors on one I²C bus?

An ESP32 talks to a BME280, an INA219, an MPU6050 and an OLED on the same two wires, scans the bus at start-up and rotates pages of readings. You need ESP32 DevKit V1, BME280 Environmental Sensor, INA219 Current Monitor, MPU6050 IMU, SSD1306 OLED Display and Breadboard 830 Tie Points. It takes 4 steps and about 70 minutes.

Level
Intermediate
Time
About 70 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
All SDA pinsESP32 GPIO21Shared data line
All SCL pinsESP32 GPIO22Shared clock line
All VCC / VINESP32 3V3Power
All GNDESP32 GNDGround
INA219 VIN+ / VIN−In series with a small load (for example an LED and 220 Ω from 3V3)Current to measure

Code

Libraries: Adafruit BME280, INA219, MPU6050 and SSD1306. Addresses used: OLED 0x3C, BME280 0x76, INA219 0x40, MPU6050 0x68: no clashes.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <Adafruit_BME280.h>
#include <Adafruit_INA219.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_SSD1306.h>

Adafruit_BME280 bme; Adafruit_INA219 ina; Adafruit_MPU6050 mpu;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
bool hasBme, hasIna, hasMpu;
int page = 0;

void scan() {
  for (byte a = 1; a < 127; a++) { Wire.beginTransmission(a); if (Wire.endTransmission() == 0) Serial.printf("Found 0x%02X\n", a); }
}

void setup() {
  Serial.begin(115200); Wire.begin(21, 22); scan();
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C); oled.setTextColor(SSD1306_WHITE);
  hasBme = bme.begin(0x76); hasIna = ina.begin(); hasMpu = mpu.begin(0x68);
}

void loop() {
  oled.clearDisplay(); oled.setTextSize(1); oled.setCursor(0, 0);
  if (page == 0) { oled.println("BME280 0x76"); if (hasBme) { oled.printf("%.1f C  %.0f %%\n%.0f hPa", bme.readTemperature(), bme.readHumidity(), bme.readPressure() / 100); } else oled.print("missing"); }
  if (page == 1) { oled.println("INA219 0x40"); if (hasIna) oled.printf("%.2f V\n%.1f mA", ina.getBusVoltage_V(), ina.getCurrent_mA()); else oled.print("missing"); }
  if (page == 2) { oled.println("MPU6050 0x68"); if (hasMpu) { sensors_event_t a, g, t; mpu.getEvent(&a, &g, &t); oled.printf("x %.1f y %.1f\nz %.1f m/s2", a.acceleration.x, a.acceleration.y, a.acceleration.z); } else oled.print("missing"); }
  oled.display();
  page = (page + 1) % 3;
  delay(2000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual ESP32 Dev Module with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Found 0x3C
Found 0x40
Found 0x68
Found 0x76

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Serial at startFour addresses: 0x3C, 0x40, 0x68 and 0x76
Unplug the MPU6050 and resetIts page says "missing", the others still work
Tilt the boardMPU6050 z reading moves away from about 9.8

If it does not work

Scanner finds nothing

SDA and SCL swapped, or no common ground.

Two modules, one address

Change one with its address pin, for example BME280 SDO to 3V3 for 0x77.

Bus hangs with all four

Too many pull-ups in parallel; remove some on the modules or shorten wires.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the four sensors on one I²C bus?

ESP32 DevKit V1, BME280 Environmental Sensor, INA219 Current Monitor, MPU6050 IMU, SSD1306 OLED Display and Breadboard 830 Tie Points.

How long does the four sensors on one I²C bus take to build?

About 70 minutes for a intermediate maker, in 4 steps.

How do I know the four sensors on one I²C bus works?

Serial at start: Four addresses: 0x3C, 0x40, 0x68 and 0x76. Unplug the MPU6050 and reset: Its page says "missing", the others still work. Tilt the board: MPU6050 z reading moves away from about 9.8.

Scanner finds nothing: what should I check?

SDA and SCL swapped, or no common ground.

Two modules, one address: what should I check?

Change one with its address pin, for example BME280 SDO to 3V3 for 0x77.

Bus hangs with all four: what should I check?

Too many pull-ups in parallel; remove some on the modules or shorten wires.