Projects / RFID memory card game

RFID memory card game

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANORFID

    Read the tags

    Print the UIDs.

  2. NANO

    Fill in the table

    Pair number for each tag.

  3. NANOSANDIS

    Add sounds

    Four tracks on the card.

  4. NANOSANDIS

    Write the game

    First card, second card, match.

  5. NANO

    Add a win

    After four pairs.

  6. NANOSANDIS

    Make the cards

    Pictures with the tag inside.

  7. NANORC522

    Build the reader box

    Reader under a thin lid.

In short

How do you build an RFID memory card game?

Children match pairs of picture cards with hidden RFID tags on a reader that says if they match. You need Arduino Nano, RC522 RFID reader, RFID tags 13.56 MHz (MIFARE Classic 1K) × 8, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10) and Resistor 1 kΩ. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
RFID SDANano D10Chip select
RFID SCK, MOSI, MISONano D13, D11, D12SPI
RFID RSTNano D9Reset
RFID 3.3V and GNDNano 3V3 and GNDPower
DFPlayer RXNano D3 through 1 kΩSound
DFPlayer TXNano D2Status
DFPlayer speaker pins8 Ω speakerSound

Code

Each card has an RFID tag taped inside and a picture on the outside; the reader hears a tag when it is held on the box top. First run the sketch and write down each tag's first UID byte from the Serial Monitor, then type them into the table, with a pair number for each; the first byte alone can repeat between tags, so for a real game use the whole four-byte UID. The MFRC522 runs at 3.3 V; most hobbyists connect it straight to a Nano, but it is safer to put a 1 kΩ and 2 kΩ divider on SCK, MOSI and SDA. Put four short sounds on the DFPlayer card: 0001 match, 0002 try again, 0003 first card and 0004 win. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails). Keep tags and loose parts away from very young children.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// RFID memory game: scan two cards, a match plays the happy sound. Libraries: MFRC522, DFRobotDFPlayerMini.
#include <SPI.h>
#include <MFRC522.h>
#include <SoftwareSerial.h>
#include <DFRobotDFPlayerMini.h>
MFRC522 rfid(10, 9);
SoftwareSerial sw(2, 3);
DFRobotDFPlayerMini dfp;
// Run once and read the UIDs from the Serial Monitor, then type each tag's first byte and pair number here.
const byte UID_FIRST[8] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00};
const byte PAIR_ID[8]   = {1, 1, 2, 2, 3, 3, 4, 4};
int first = -1, turns = 0, found = 0;
int cardIndex() {
  for (int i = 0; i < 8; i++) if (rfid.uid.uidByte[0] == UID_FIRST[i]) return i;
  return -1;
}
void setup() {
  Serial.begin(9600);
  SPI.begin(); rfid.PCD_Init();
  sw.begin(9600);
  if (dfp.begin(sw)) dfp.volume(15);
}
void loop() {
  if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) return;
  Serial.print("UID first byte: "); Serial.println(rfid.uid.uidByte[0], HEX);   // use this to fill in the table
  int c = cardIndex();
  rfid.PICC_HaltA();
  if (c < 0) return;
  if (first < 0) { first = c; dfp.play(3); delay(600); return; }
  if (c == first) return;
  turns++;
  if (PAIR_ID[c] == PAIR_ID[first]) { found++; dfp.play(1); }
  else dfp.play(2);
  first = -1;
  if (found == 4) { dfp.play(4); found = 0; turns = 0; }
  delay(1000);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Scan a cardFirst-card sound
Scan its pairMatch sound
Scan a different oneTry-again sound
Four pairs foundWin sound and reset

If it does not work

No card read

Hold it flat and closer to the reader.

Wrong matches

Use the full UID, not one byte.

No sound

Check the file names and the RX resistor.

Reader fails after a while

Check the 3.3 V supply.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the RFID memory card game?

Arduino Nano, RC522 RFID reader, RFID tags 13.56 MHz (MIFARE Classic 1K) × 8, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10) and Resistor 1 kΩ.

How long does the RFID memory card game take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the RFID memory card game works?

Scan a card: First-card sound. Scan its pair: Match sound. Scan a different one: Try-again sound.

No card read: what should I check?

Hold it flat and closer to the reader.

Wrong matches: what should I check?

Use the full UID, not one byte.

No sound: what should I check?

Check the file names and the RX resistor.

Reader fails after a while: what should I check?

Check the 3.3 V supply.