Build it step by step
0 of 7 doneWire the circuit
Battery plus, the 470 ohm resistor, the pot, battery minus.
Measure the battery
Note its voltage with nothing connected to the pot.
Set the pot to about 100 ohms
Turn it near one end and note VL.
Work out RL and the power
Use the two formulas.
Repeat at ten settings
Go through 100, 250, 470, 750 ohms and so on.
Plot power against RL
Draw the curve and mark the peak.
Compare
The peak should sit at 470 ohms.
How do you build a maximum power transfer lab?
Put a 470 ohm resistor in series with a 9 V battery to stand for its internal resistance, vary a 1 kilohm pot as the load and work out the power at each setting. The peak appears when the load equals the source resistance. You need Potentiometer 1 kΩ (linear), Resistor 470 Ω, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 7
Parts list
- PassivesBuy
- PassivesBuyResistor 470 Ω × 1
- Tools & InstrumentsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Battery plus (red lead) | 470 ohm resistor leg 1 | The resistor stands in for the source's internal resistance |
| 470 ohm resistor leg 2 | Pot outer leg and the meter red probe | The load node |
| Pot middle leg joined to the other outer leg | Battery minus (black lead) and the meter black probe | A pot used as a variable resistor |
| Meter dial | DC volts, 20 V range | Measures the voltage across the pot |
No code needed
No code. The 470 ohm resistor and the pot form a divider across the battery, and the pot is the load. Measure the voltage across the pot, call it VL, with the battery voltage Vb. The pot's resistance is RL = 470 x VL divided by (Vb minus VL), and the power in the load is P = VL squared divided by RL. For a 9 V battery, a 100 ohm load gets about 25 mW, 250 ohms about 39 mW, 470 ohms about 43 mW, 750 ohms about 41 mW and 1 kilohm about 38 mW, so the peak is at 470 ohms, the same as the source resistance. This is the maximum power transfer rule. It matters for loudspeakers, antennas and sensors, but note that at the peak half the power is wasted in the source, so power systems aim for a much smaller source resistance instead. Only a tiny current flows here, so nothing gets hot.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| RL near 100 ohms | About 25 mW |
| RL near 250 ohms | About 39 mW |
| RL near 470 ohms | About 43 mW, the peak |
| RL near 1 kilohm | About 38 mW |
| VL at the peak | Half the battery voltage, about 4.5 V |
If it does not work
Peak is not at 470 ohms
The pot may not be linear or its range does not reach 470 ohms.
Voltage never changes
Check the meter is across the pot and the pot is wired as a variable resistor.
Power numbers look huge
Convert millivolts and milliwatts carefully.
Battery voltage sags
The battery is tired, so use a fresh one.
Readings wander
Hold the pot still and clean the contacts by turning it a few times.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the maximum power transfer lab?
Potentiometer 1 kΩ (linear), Resistor 470 Ω, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the maximum power transfer lab take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the maximum power transfer lab works?
RL near 100 ohms: About 25 mW. RL near 250 ohms: About 39 mW. RL near 470 ohms: About 43 mW, the peak.
Peak is not at 470 ohms: what should I check?
The pot may not be linear or its range does not reach 470 ohms.
Voltage never changes: what should I check?
Check the meter is across the pot and the pot is wired as a variable resistor.
Power numbers look huge: what should I check?
Convert millivolts and milliwatts carefully.
Battery voltage sags: what should I check?
The battery is tired, so use a fresh one.
