Build it step by step
0 of 7 doneDraw the plan
Gate 1 inverts the tip, gate 2 inverts it again, gate 3 inverts the stretched pulse. Mark pin numbers before you place parts.
Place the chip and power
Put the 74HC14 across the breadboard centre gap. Connect pin 14 to the red clip and pin 7 to the black clip.
Wire the input and the pull-down
Probe tip to pin 1 with a 1 MΩ resistor to GND.
Wire the LEDs
Each LED anode through 330 Ω to VCC, each cathode to its output pin as in the table.
Add the pulse stretcher
From pin 4 through the 1N4148 to a node with 100 nF and 1 MΩ to GND, and the node goes to pin 5.
Tie off unused inputs
Pins 9, 11 and 13 to GND.
Try it
Clip to a 5 V board, touch the tip to 5 V, GND and a toggling pin.
How do you build a pocket logic probe?
A pen-shaped probe shows high, low or pulsing on a digital line with three LEDs. You need 74HC14 hex Schmitt-trigger inverter, LED 5 mm red, LED 5 mm green, LED 5 mm yellow, Resistor 330 Ω × 3, Resistor 1 MΩ × 2, Signal Diode 1N4148, Ceramic Capacitor 100 nF, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 10
Parts list
- Integrated CircuitsBuy
- SemiconductorsBuyLED 5 mm red × 1
- SemiconductorsBuyLED 5 mm green × 1
- SemiconductorsBuyLED 5 mm yellow × 1
- PassivesBuyResistor 330 Ω × 3
- PassivesBuyResistor 1 MΩ × 2One pulls the tip low, one stretches pulses
- SemiconductorsBuy
- PassivesBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Red clip lead | 74HC14 pin 14 (VCC) | Power from the circuit under test, 3 to 5 V |
| Black clip lead | 74HC14 pin 7 (GND) | Common ground |
| Probe tip | Pin 1 (gate 1 input) | Input |
| 1 MΩ | Probe tip to GND | An open probe then reads low |
| Pin 2 (gate 1 output) | Pin 3 (gate 2 input) and the red LED cathode | Inverted signal, red lights when the tip is high |
| Pin 4 (gate 2 output) | Green LED cathode, and 1N4148 anode | Green lights when the tip is low |
| 1N4148 cathode | Node X with 100 nF to GND and 1 MΩ to GND | Pulse stretcher, about 0.1 s hold |
| Node X | Pin 5 (gate 3 input) | Held high after a pulse |
| Pin 6 (gate 3 output) | Yellow LED cathode | Yellow lights while a pulse is held |
| LED anodes | 330 Ω each to VCC | Current limit |
| Unused inputs pin 9, 11, 13 | GND | Never leave CMOS inputs floating |
No code needed
No code. The 74HC14 inverts, so each LED is wired from VCC through a 330 Ω to the gate output and lights when that output is low. At 5 V each LED draws about 9 mA, within the chip's output rating.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Tip on 5 V | Red on, green off, yellow on |
| Tip on GND | Green on, red off, yellow off |
| Tip on a 1 Hz blinking pin | Red and green alternate and yellow stays on |
| Tip open | Reads low through the 1 MΩ, so green is on |
If it does not work
All three LEDs lit
An unused input is floating. Tie pins 9, 11 and 13 to GND.
LEDs very dim
The supply is below 3 V or LEDs are in the wrong direction.
Yellow never lights
Check the 1N4148 direction: its stripe (cathode) points to the node.
Probe reads wrong levels
The circuit under test uses 3.3 V and the probe's red lead is on 5 V. Power it from the same rail.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the pocket logic probe?
74HC14 hex Schmitt-trigger inverter, LED 5 mm red, LED 5 mm green, LED 5 mm yellow, Resistor 330 Ω × 3, Resistor 1 MΩ × 2, Signal Diode 1N4148, Ceramic Capacitor 100 nF, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). Resistor 1 MΩ × 2: One pulls the tip low, one stretches pulses.
How long does the pocket logic probe take to build?
About 60 minutes for a beginner maker, in 7 steps.
How do I know the pocket logic probe works?
Tip on 5 V: Red on, green off, yellow on. Tip on GND: Green on, red off, yellow off. Tip on a 1 Hz blinking pin: Red and green alternate and yellow stays on.
All three LEDs lit: what should I check?
An unused input is floating. Tie pins 9, 11 and 13 to GND.
LEDs very dim: what should I check?
The supply is below 3 V or LEDs are in the wrong direction.
Yellow never lights: what should I check?
Check the 1N4148 direction: its stripe (cathode) points to the node.
Probe reads wrong levels: what should I check?
The circuit under test uses 3.3 V and the probe's red lead is on 5 V. Power it from the same rail.
