Projects / Liquid density meter

Liquid density meter

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO++516 g

    Mount the load cell

    Fix one end to a base and put a platform on the other end.

  2. NANO++517 g

    Wire the HX711

    VCC and GND, DT to D4, SCK to D5, and the four load cell wires.

  3. NANO13.6 mASSD1306

    Wire the display and button

    OLED to A4 and A5, button D2 to GND.

  4. NANO+519 gSSD1306

    Install the libraries

    HX711, SSD1306 and GFX.

  5. NANO

    Calibrate

    Put a known weight on and find the factor from the raw value.

  6. NANO

    Zero the empty cup

    Press the button.

  7. NANO

    Fill to the mark

    Read the density of each liquid.

In short

How do you build a liquid density meter?

A load cell and an HX711 weigh a cup filled to a mark and a Nano works out the density, so you can compare water, salt water and sugar water. You need Arduino Nano, HX711 load cell amplifier, Load cell 1 kg, SSD1306 OLED Display, Tactile push button 6 mm, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
HX711 VCCNano 5VPower at 5 V
HX711 GNDNano GNDCommon ground
HX711 DTNano D4Data
HX711 SCKNano D5Clock
Load cell redHX711 E+Bridge excitation plus
Load cell blackHX711 E-Bridge excitation minus
Load cell whiteHX711 A-Signal minus (swap with A+ if the weight reads negative)
Load cell greenHX711 A+Signal plus
OLED SDA and SCLNano A4 and A5I2C, address 0x3C (VCC and GND to 5V and GND)
Tare buttonNano D2 and GNDZeros the empty cup

Code

Density is mass divided by volume. A load cell is a metal bar with strain gauges on it that change resistance when it bends, and the HX711 is an amplifier and converter that turns the tiny signal into a number. A cup on a platform on the load cell lets the Nano weigh what you put in it. Fill the cup exactly to a mark, which is a known volume such as 100 millilitres measured with a syringe, press the tare button with the empty cup on to zero the scale, then weigh each liquid. Fresh water gives about 1.00 grams per millilitre, and salt water gives more, for example about 1.07 for a heavy solution. To calibrate, put a known weight such as a 100 gram standard on the platform, read the raw number in the Serial Monitor, divide it by the weight and enter that as the calibration factor in the sketch. Do not put more than a kilogram on the load cell, and do not press hard on it, because it bends only a tiny amount. Keep liquids well away from the electronics and clean up any spill at once. Results are good to a percent or two at best, which is enough to tell water, salt water and sugar water apart.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <HX711.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

HX711 scale;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);

const int DT = 4, SCK_PIN = 5, TARE_BUTTON = 2;
const float CAL_FACTOR = 420.0;                    // change after calibrating with a known weight
const float CUP_VOLUME_ML = 100.0;                 // the volume up to the fill mark, measured with a syringe or cylinder

void setup() {
  pinMode(TARE_BUTTON, INPUT_PULLUP);
  Serial.begin(9600);
  scale.begin(DT, SCK_PIN);
  scale.set_scale(CAL_FACTOR);
  scale.tare();
  Wire.begin();
  if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) { while (true) {} }
}

void loop() {
  if (digitalRead(TARE_BUTTON) == LOW) {
    scale.tare();                                  // set the empty cup as zero
    delay(300);
  }

  float grams = scale.get_units(10);               // average of ten readings
  float density = grams / CUP_VOLUME_ML;           // grams per millilitre

  Serial.print("raw ");
  Serial.print(scale.get_value(10));
  Serial.print("  grams ");
  Serial.println(grams);

  oled.clearDisplay();
  oled.setTextColor(SSD1306_WHITE);
  oled.setTextSize(1);
  oled.setCursor(0, 0);
  oled.print("Liquid in the cup");
  oled.setTextSize(2);
  oled.setCursor(0, 16);
  oled.print(grams, 1);
  oled.print(" g");
  oled.setCursor(0, 38);
  oled.print(density, 3);
  oled.setTextSize(1);
  oled.print(" g/mL");
  oled.setCursor(0, 56);
  oled.print("Press button: zero");
  oled.display();
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

raw 0  grams 0.00

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Empty cup after tare0 g
Known weight on the platformMatches within a gram
Cup of tap water to the markAbout 1.00 g/mL
Cup of salt waterHigher than water
Press the button on the empty cupBack to zero

If it does not work

Reading is negative

Swap the A+ and A- wires.

Reading drifts

Wait for the load cell to warm up and keep it away from drafts.

Wrong by a fixed factor

Recalibrate with a known weight.

Jumpy numbers

Fix the load cell firmly and keep wires still.

Display blank

Check the OLED address 0x3C.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the liquid density meter?

Arduino Nano, HX711 load cell amplifier, Load cell 1 kg, SSD1306 OLED Display, Tactile push button 6 mm, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the liquid density meter take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the liquid density meter works?

Empty cup after tare: 0 g. Known weight on the platform: Matches within a gram. Cup of tap water to the mark: About 1.00 g/mL.

Reading is negative: what should I check?

Swap the A+ and A- wires.

Reading drifts: what should I check?

Wait for the load cell to warm up and keep it away from drafts.

Wrong by a fixed factor: what should I check?

Recalibrate with a known weight.

Jumpy numbers: what should I check?

Fix the load cell firmly and keep wires still.