Projects / Two-transistor LED flasher

Two-transistor LED flasher

Beginner30 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. BC547

    Place the transistors

    Two BC547 side by side with emitters to ground.

  2. 18.6 mA

    Add the loads

    A 1 kΩ and an LED in each collector to +9 V.

  3. Bias the bases

    47 kΩ from +9 V to each base.

  4. Cross-couple

    C1 from collector 1 to base 2, C2 from collector 2 to base 1, positive legs on the collectors.

  5. 18.7 mA

    Power up

    The LEDs flash alternately.

  6. Experiment

    Use 100 µF in place of 10 µF and see the rate fall to about one tenth.

  7. Look at waveforms

    If you have a scope, watch the collectors and the bases.

In short

How do you build a two-transistor LED flasher?

Two transistors flash two LEDs in turn, the classic astable multivibrator. You need BC547 NPN transistor × 2, Resistor 1 kΩ × 2, Resistor 47 kΩ × 2, Electrolytic capacitor 10 µF × 2, LED 5 mm red, LED 5 mm green, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
9
See the electronics first. This build uses transistor switch. Try a transistor switch in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Q1 collectorRed LED cathode, and the positive side of C1Collector 1
Red LED anode1 kΩ to 9 V +Load resistor
Q2 collectorGreen LED cathode, and the positive side of C2Collector 2
Green LED anode1 kΩ to 9 V +Load resistor
C1 negativeQ2 baseCross-coupling
C2 negativeQ1 baseCross-coupling
Q1 base47 kΩ to 9 V +Base bias
Q2 base47 kΩ to 9 V +Base bias
Both emittersGNDCommon ground

No code needed

No code. Each half of the cycle lasts about 0.7 × R × C = 0.7 × 47 kΩ × 10 µF, roughly 0.33 s, so each LED blinks about 1.5 times a second. The capacitors' positive legs go to the collectors, which are the more positive side.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onLEDs alternate about 1.5 times per second
Replace both capacitors with 100 µFAbout 0.15 Hz, a slow alternate
Unequal capacitorsOne LED stays on longer
Collector waveformSquare-ish with a rounded rise

If it does not work

Both LEDs stay lit

The circuit locked up. Touch a base with a finger or power it again.

Does not oscillate

The capacitor polarity is wrong, or a transistor is damaged.

Very fast, appears steady

The capacitors are too small. Use 10 µF or more.

One LED never lights

Check its direction and the collector resistor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the two-transistor LED flasher?

BC547 NPN transistor × 2, Resistor 1 kΩ × 2, Resistor 47 kΩ × 2, Electrolytic capacitor 10 µF × 2, LED 5 mm red, LED 5 mm green, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.

How long does the two-transistor LED flasher take to build?

About 30 minutes for a beginner maker, in 7 steps.

How do I know the two-transistor LED flasher works?

Power on: LEDs alternate about 1.5 times per second. Replace both capacitors with 100 µF: About 0.15 Hz, a slow alternate. Unequal capacitors: One LED stays on longer.

Both LEDs stay lit: what should I check?

The circuit locked up. Touch a base with a finger or power it again.

Does not oscillate: what should I check?

The capacitor polarity is wrong, or a transistor is damaged.

Very fast, appears steady: what should I check?

The capacitors are too small. Use 10 µF or more.

One LED never lights: what should I check?

Check its direction and the collector resistor.