Build it step by step
0 of 7 doneBuild the clock
Wire the 555 astable and check pin 3 with a single LED and resistor.
Add the counter
Connect pin 3 to the 4017 clock pin and its power pins.
Add the LEDs
Put an LED and 1 kΩ resistor on each output.
Watch it chase
One LED should light at a time and move along.
Change the speed
Turn the pot.
Shorten the run
Link Q6 (pin 5) to reset (pin 15) to use six LEDs.
Slow it down
Swap the capacitor for 100 µF.
How do you build an LED chaser with 555 and 4017?
A 555 clock steps a CD4017 counter so ten LEDs light one after another, with a pot for speed. You need NE555 Timer IC, CD4017 Counter, LED 5 mm red × 10, Resistor 1 kΩ × 10, Resistor 10 kΩ, Potentiometer 10 kΩ, Electrolytic capacitor 10 µF, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 11
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- Integrated CircuitsBuyCD4017 Counter × 1
- SemiconductorsBuyLED 5 mm red × 10
- PassivesBuyResistor 1 kΩ × 10
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- PassivesBuy
- PrototypingBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + | + rail | Supply |
| 9 V battery - | - rail | Ground |
| 555 pin 8 and pin 4 | + rail | Power and reset high |
| 555 pin 1 | - rail | Ground |
| 10 kΩ resistor (R1) | + rail and 555 pin 7 | Timing resistor |
| Potentiometer (two pins) | 555 pin 7 and pin 6 | Timing resistor, speed control |
| 555 pin 2 and pin 6 | Joined | Astable connection |
| 10 µF capacitor | 555 pin 6 and - rail, + on pin 6 | Timing capacitor |
| 555 pin 3 | CD4017 pin 14 (CLK) | Clock |
| CD4017 pin 16 | + rail | Power |
| CD4017 pin 8 | - rail | Ground |
| CD4017 pin 13 (clock enable) | - rail | Enable counting |
| CD4017 pin 15 (reset) | - rail | Ten-step run; link to Q6 for a six-step run |
| CD4017 outputs Q0 to Q9 | Pins 3, 2, 4, 7, 10, 1, 5, 6, 9, 11 | One output per LED |
| Ten 1 kΩ resistors and LEDs | From each output through the resistor and an LED to - rail | The ten LEDs |
No code needed
No code. The 555 in astable mode gives a clock of about f = 1.44 ÷ ((R1 + 2·Rpot) × C), which is roughly 5 to 14 Hz with 10 kΩ, a 10 kΩ pot and 10 µF; swap in a 100 µF capacitor to slow it right down. The CD4017 is a decade counter, and each clock pulse moves a high on to the next of its ten outputs. Its outputs supply only a few milliamps, so 1 kΩ resistors give modest, safe brightness; for brighter LEDs add a transistor on each output. To shorten the run, link a later output to the reset pin: connecting Q6 (pin 5) to reset (pin 15) makes it count only Q0 to Q5. Use a 9 V battery or four AA cells; both chips accept it.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Power on | One LED lit at a time |
| Pot turned | Chase speed changes |
| Q6 linked to reset | Only six LEDs light in turn |
| 100 µF capacitor | Much slower chase |
If it does not work
No LEDs
Check the 4017 power pins 16 and 8 and the 555 output.
Two LEDs lit
Check the reset pin is not floating.
Chase does not move
Check clock enable pin 13 goes to ground.
Dim LEDs
Normal at these resistor values; use transistors for bright ones.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the LED chaser with 555 and 4017?
NE555 Timer IC, CD4017 Counter, LED 5 mm red × 10, Resistor 1 kΩ × 10, Resistor 10 kΩ, Potentiometer 10 kΩ, Electrolytic capacitor 10 µF, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack.
How long does the LED chaser with 555 and 4017 take to build?
About 60 minutes for a beginner maker, in 7 steps.
How do I know the LED chaser with 555 and 4017 works?
Power on: One LED lit at a time. Pot turned: Chase speed changes. Q6 linked to reset: Only six LEDs light in turn.
No LEDs: what should I check?
Check the 4017 power pins 16 and 8 and the 555 output.
Two LEDs lit: what should I check?
Check the reset pin is not floating.
Chase does not move: what should I check?
Check clock enable pin 13 goes to ground.
Dim LEDs: what should I check?
Normal at these resistor values; use transistors for bright ones.
