LDR response curve lab
Wire an LDR in a divider and read it at several distances from a torch and in the dark. Work out its resistance for each light level and plot the curve to choose the best fixed resistor.
Build it step by step
0 of 7 doneWire the divider
9 V plus to the LDR, the LDR to a 10 kilohm resistor, the resistor to 9 V minus.
Measure in the dark
Cover the LDR with a box and note Vout.
Measure in room light
Note Vout and work out the resistance.
Shine the torch from 100, 50, 25, 10 and 5 cm
Note Vout at each distance.
Swap the fixed resistor to 1 kilohm and then 100 kilohm
Repeat the readings.
Work out the LDR resistance each time
Use Rldr = R x (9 minus Vout) divided by Vout.
Plot all three curves
See which resistor gives the widest voltage swing.
How do you build an LDR response curve lab?
Wire an LDR in a divider and read it at several distances from a torch and in the dark. Work out its resistance for each light level and plot the curve to choose the best fixed resistor. You need LDR Photoresistor, Resistor 1 kΩ, Resistor 10 kΩ, Resistor 100 kΩ, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 9
Parts list
- SensorsBuy
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuyResistor 100 kΩ × 1
- Tools & InstrumentsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Battery plus (red lead) | LDR leg 1 | Supply to the top of the divider |
| LDR leg 2 | Fixed resistor leg 1 and the meter red probe | The divider output |
| Fixed resistor leg 2 | Battery minus (black lead) and the meter black probe | Ground |
| Meter dial | DC volts, 20 V range | Reads the voltage across the fixed resistor |
No code needed
No code. The LDR and the fixed resistor share the 9 V of the battery, and the meter reads the voltage across the fixed resistor. The fixed resistor's voltage is Vout = 9 x R / (R + Rldr), so the LDR's resistance is Rldr = R x (9 minus Vout) divided by Vout. In a dark room an LDR can be about a megohm, in normal room light around 10 to 50 kilohms and close to a phone torch a few kilohms or less, so its resistance changes by hundreds of times. Plot the resistance against the light level on a log scale and you will see roughly a straight line, which is why an LDR is good at telling light from dark but poor at giving exact numbers. The best fixed resistor is close to the LDR's resistance in the middle of the range you care about, which gives the widest swing of voltage. Do not stare into a torch at close range.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Dark with 10 kilohms | Vout under 0.5 V |
| Room light with 10 kilohms | About 1 to 5 V |
| Torch at 5 cm | About 6 to 8 V |
| Same readings with 100 kilohms | Larger voltages in the dark, saturates in bright light |
| Same readings with 1 kilohm | Small voltages at all but the brightest light |
If it does not work
Vout never changes
Check the LDR is in the divider and the meter is across the fixed resistor.
Readings jump about
Mains lights flicker, try daylight or a steady torch.
Numbers differ a lot from these
LDRs vary widely, so use your own curve.
Resistance works out negative
You have swapped Vout, so read across the fixed resistor.
LDR slow to settle
Wait a few seconds after changing the light.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the LDR response curve lab?
LDR Photoresistor, Resistor 1 kΩ, Resistor 10 kΩ, Resistor 100 kΩ, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the LDR response curve lab take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the LDR response curve lab works?
Dark with 10 kilohms: Vout under 0.5 V. Room light with 10 kilohms: About 1 to 5 V. Torch at 5 cm: About 6 to 8 V.
Vout never changes: what should I check?
Check the LDR is in the divider and the meter is across the fixed resistor.
Readings jump about: what should I check?
Mains lights flicker, try daylight or a steady torch.
Numbers differ a lot from these: what should I check?
LDRs vary widely, so use your own curve.
Resistance works out negative: what should I check?
You have swapped Vout, so read across the fixed resistor.
