Build it step by step
0 of 7 doneBuild the supply
Two 9 V in series, check plus and minus.
Wire one preamp
Mic, bias, 10 uF, gain stage.
Check with headphones
Speak into the mic.
Add the level pot
One per input.
Add the summing stage
Combine three pots.
Add the master pot and jack
Output.
Add the second mic and phone
Mix all three.
How do you build a two-mic karaoke mixer?
An op-amp summing mixer blends two microphones and a phone into one output, with a level for each. You need LM324 quad op-amp, Electret microphone (capsule) × 2, Potentiometer 10 kΩ × 4, Resistor 10 kΩ × 8, Resistor 100 kΩ × 2, Electrolytic capacitor 10 µF × 4, Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery × 2, 9 V battery snap with DC jack × 2 and Perfboard (dot PCB) 7 × 9 cm. It takes 7 steps and about 150 minutes.
- Level
- Intermediate
- Time
- About 150 min
- Parts
- 10
Parts list
- Integrated CircuitsBuy
- AudioBuy
- PassivesBuy
- PassivesBuyResistor 10 kΩ × 8
- PassivesBuyResistor 100 kΩ × 2
- PassivesBuy
- ConnectorsBuy
- BatteriesBuy9 V battery × 2
- PowerBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Two 9 V batteries in series | Join plus of one to minus of the other | That joint is ground, ends are +9 V and -9 V |
| LM324 pin 4 | +9 V | Positive supply |
| LM324 pin 11 | -9 V | Negative supply |
| Each mic capsule | 10k to +9 V, capsule minus to ground, 10 uF to the stage input | Bias and coupling (plus pin on the 10k side) |
| Preamp A (pins 1, 2, 3) | 10k from coupling to pin 2, 100k from pin 1 to pin 2, pin 3 to ground | Gain of about 10 inverting |
| Preamp B (pins 7, 6, 5) | Same as A with pin 7, 6, 5 | Second mic |
| Level pots | Preamp output to pot top, pot bottom to ground, wiper to 10k | One per input |
| Phone input | Jack tip through 10 uF to its level pot | Third input |
| Summing stage (pins 8, 9, 10) | Three 10k from wipers to pin 9, 10k from pin 8 to pin 9, pin 10 to ground | Mixes and inverts |
| Master pot | Pin 8 through 10 uF to pot top, wiper to output jack tip | Output level |
| Unused amplifier (pins 12, 13, 14) | Pin 14 to pin 13, pin 12 to ground | Parks the spare section |
No code needed
A summing amplifier is an inverting op-amp with several input resistors meeting at one point, called the virtual earth, so each input adds to the output without affecting the others; that is why a mixer can have a separate level for each source. Each microphone first goes through a gain-of-ten stage because a capsule gives only a few millivolts. Two 9 V batteries in series give a plus and a minus supply, which means the signal can swing around zero and no mid-point bias network is needed. Switch off when finished, because batteries drain even with no sound. The LM324 is a general-purpose part and adds a little crossover buzz at low levels; a TL072 on the same pinout would sound cleaner, but the circuit works with either. Keep the mics away from the speakers or the whole thing will howl; this is normal feedback, so turn the levels down. Use powered speakers or headphones at a modest volume. There is no code for this build.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Supply | About +9 V and -9 V against the joint |
| One mic | Voice is audible at the output |
| Phone playing | Music joins the voice |
| Each level pot | Changes only its own input |
If it does not work
Silence
Check the +9 V bias reaches the mic and the 10 uF faces the right way.
Loud hum
Keep leads short and the input pots grounded.
Whistling
Move the mics away from the speakers.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the two-mic karaoke mixer?
LM324 quad op-amp, Electret microphone (capsule) × 2, Potentiometer 10 kΩ × 4, Resistor 10 kΩ × 8, Resistor 100 kΩ × 2, Electrolytic capacitor 10 µF × 4, Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery × 2, 9 V battery snap with DC jack × 2 and Perfboard (dot PCB) 7 × 9 cm.
How long does the two-mic karaoke mixer take to build?
About 150 minutes for a intermediate maker, in 7 steps.
How do I know the two-mic karaoke mixer works?
Supply: About +9 V and -9 V against the joint. One mic: Voice is audible at the output. Phone playing: Music joins the voice.
Silence: what should I check?
Check the +9 V bias reaches the mic and the 10 uF faces the right way.
Loud hum: what should I check?
Keep leads short and the input pots grounded.
Whistling: what should I check?
Move the mics away from the speakers.
