Projects / Two-room wired intercom

Two-room wired intercom

Intermediate3 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Build one station

    Mic, amplifier and speaker.

  2. Test it alone

    Hear your voice with the gain low.

  3. Build the second

    Same circuit.

  4. MULTI

    Wire the cable

    Four cores as planned.

  5. 13.1 mA

    Add the talk buttons

    Switch between listen and talk.

  6. 13.1 mA

    Add the call buzzer

    A second button and a buzzer.

  7. ABS

    Box both

    Cut holes for the speaker and mic.

In short

How do you build a two-room wired intercom?

Two stations with a mic, an LM386 and a talk button let you speak between rooms over a 4-core cable. You need LM386 amplifier module × 2, Electret microphone (capsule) × 2, Speaker 8 Ω 0.5 W × 2, Push button 16 mm metal (momentary, LED) × 2, Multi-core shielded cable 4-core, Resistor 10 kΩ × 2, Electrolytic capacitor 10 µF × 2, 12 V 2 A DC adapter and ABS project box (100 × 60 × 25 mm) × 2. It takes 7 steps and about 180 minutes.

Level
Intermediate
Time
About 180 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Each station microphone10 kΩ bias to 5 V, 10 µF to amplifier inputMic stage
Cable core 1Audio from station A to BA to B
Cable core 2Audio from station B to AB to A
Cable cores 3 and 4Supply plus and groundShared power
Talk buttonConnects the speaker to the line while pressedPush-to-talk
Cable shieldGround at one end onlyNoise screen
12 V adapterFuse (1 A), then cores 3 and 4Supply

No code needed

Push-to-talk keeps the circuit simple: when you hold your button, your microphone feeds the line and the other station's amplifier plays it through its speaker, and when nobody holds a button both stations listen. Hold your button down and speak toward the capsule; if you hear a loud squeal, the speaker and microphone are feeding back, so face them apart or lower the gain. The shared supply travels over the cable's other two cores, so keep the cable short, use a 12 V adapter with a fuse, and run the shield to ground at one end only to avoid a ground loop hum. Use a small buzzer and a second button to call the other room if you wish. Keep the cable and wires away from mains, and use it only indoors.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hold A's buttonB hears A
ReleaseB's speaker is quiet
SquealDisappears with lower gain
Cable humQuiet with the shield grounded at one end

If it does not work

No sound

Check the bias on the microphone.

Squeal

Lower gain or move apart.

Hum

Earth the shield at one end only.

Weak sound

Use a shorter cable or a larger supply.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the two-room wired intercom?

LM386 amplifier module × 2, Electret microphone (capsule) × 2, Speaker 8 Ω 0.5 W × 2, Push button 16 mm metal (momentary, LED) × 2, Multi-core shielded cable 4-core, Resistor 10 kΩ × 2, Electrolytic capacitor 10 µF × 2, 12 V 2 A DC adapter and ABS project box (100 × 60 × 25 mm) × 2.

How long does the two-room wired intercom take to build?

About 180 minutes for a intermediate maker, in 7 steps.

How do I know the two-room wired intercom works?

Hold A's button: B hears A. Release: B's speaker is quiet. Squeal: Disappears with lower gain.

No sound: what should I check?

Check the bias on the microphone.

Squeal: what should I check?

Lower gain or move apart.

Hum: what should I check?

Earth the shield at one end only.

Weak sound: what should I check?

Use a shorter cable or a larger supply.