Projects / Hot potato beeper

Hot potato beeper

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO8.2 mA

    Wire the button, buzzer and LED

    D2, D8 and D9.

  2. NANO

    Upload and open the serial monitor at 9600

    It says Press the button to light the fuse.

  3. NANO

    Press the button

    Slow beeps begin.

  4. NANO

    Listen as the beeps speed up

    The pitch climbs.

  5. NANO

    Wait for the long buzz

    The round ends.

  6. NANO

    Play a few rounds

    Fuse times are different each time.

  7. NANO

    Change the fuse range

    Make it shorter or longer.

In short

How do you build a hot potato beeper?

A small box beeps faster and faster while players pass it round, then gives a long buzz at a random moment and the player holding it is out. Press its button to start a round. A fast party game that is also a lesson in random timing. You need Arduino Nano, Tactile push button 6 mm, Passive buzzer, LED 5 mm red, Resistor 220 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Button leg 1Nano D2Start and pass button
Button leg 2Nano GNDPressing joins D2 to ground
Passive buzzer +Nano D8Tone output
Passive buzzer -Nano GNDReturn path
LED long legNano D9 through a 220 ohm resistorFlashes with each beep
LED short legNano GNDReturn path

Code

The game is a state machine with two states: waiting, and burning the fuse. When you press the button the Nano picks a random fuse time of 8 to 25 seconds that nobody knows. While the fuse burns, a short beep and a flash repeat, and the gap between them shrinks from nearly a second to a tenth of a second, while the pitch climbs, so the tension builds. At the end the buzzer gives a long low sound and the player holding the box is out. The button is pressed to start the round and, if you like, clicks as the box is passed. The random seed combines a floating analog pin with the microsecond clock so each game differs. The buzzer can be loud, so keep it a hand-span from your ear. Try changing the fuse range, or making the pass button shorten the fuse by a little to keep players honest.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t BUTTON_PIN = 2;
const uint8_t BUZZER_PIN = 8;
const uint8_t LED_PIN = 9;

enum State { IDLE, RUNNING };
State state = IDLE;
unsigned long roundStart, fuseMs, lastBeep;

bool pressed() {
  if (digitalRead(BUTTON_PIN) == LOW) {
    delay(30);
    while (digitalRead(BUTTON_PIN) == LOW) {}   // wait for release
    return true;
  }
  return false;
}

void beep(int hz, int ms) {
  tone(BUZZER_PIN, hz, ms);
  digitalWrite(LED_PIN, HIGH);
  delay(ms);
  digitalWrite(LED_PIN, LOW);
}

void setup() {
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  pinMode(LED_PIN, OUTPUT);
  randomSeed(analogRead(A0) + micros());
  Serial.begin(9600);
  Serial.println("Press the button to light the fuse.");
}

void loop() {
  if (state == IDLE) {
    if (pressed()) {
      fuseMs = random(8000, 25000);             // a secret fuse of 8 to 25 seconds
      roundStart = millis();
      lastBeep = 0;
      state = RUNNING;
      Serial.println("Fuse lit. Pass it on!");
    }
    return;
  }
  unsigned long elapsed = millis() - roundStart;
  if (elapsed >= fuseMs) {                      // boom
    tone(BUZZER_PIN, 220, 2000);
    digitalWrite(LED_PIN, HIGH);
    delay(2000);
    digitalWrite(LED_PIN, LOW);
    Serial.println("BUZZ! The player holding it is out. Press for another round.");
    state = IDLE;
    return;
  }
  float progress = (float)elapsed / fuseMs;       // 0 to 1
  unsigned long gap = 900 - (unsigned long)(progress * 800);   // 900 ms slowing to 100 ms
  if (millis() - lastBeep >= gap) {
    lastBeep = millis();
    beep(1000 + (int)(progress * 800), 40);       // pitch rises as the fuse burns
  }
  if (pressed()) beep(2000, 20);                  // a little click when it is passed
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Press the button to light the fuse.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Button pressFuse lights, slow beeps start
During the roundBeeps get faster and higher
Fuse endsLong low buzz and a lit LED
Another roundA different fuse time
Pass clickA short high click when you press mid-round

If it does not work

No sound

Check you have a passive buzzer and it is on D8.

Round ends instantly

Check the fuse range in random().

Same fuse every time

Check the floating A0 pin is not wired to anything.

LED never flashes

Check its direction.

Button seems stuck

Check it is wired to D2 and GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the hot potato beeper?

Arduino Nano, Tactile push button 6 mm, Passive buzzer, LED 5 mm red, Resistor 220 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the hot potato beeper take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the hot potato beeper works?

Button press: Fuse lights, slow beeps start. During the round: Beeps get faster and higher. Fuse ends: Long low buzz and a lit LED.

No sound: what should I check?

Check you have a passive buzzer and it is on D8.

Round ends instantly: what should I check?

Check the fuse range in random().

Same fuse every time: what should I check?

Check the floating A0 pin is not wired to anything.

LED never flashes: what should I check?

Check its direction.