Build it step by step
0 of 8 doneWire the sensor
5V, GND, output to D2 with a 10 kilohm pull-up.
Wire the servo
Signal D9, power 5V and GND.
Wire the LEDs
Red D4, green D5, with 220 ohm each.
Upload the sketch
Red LED on, servo at the locked angle.
Try the magnet
Move it to the marked face of the sensor.
Flip the magnet
Only one pole works.
Check the relock
It locks after ten seconds.
Mount in a box
Fix the sensor behind the lid where the magnet goes.
How do you build a magnet-key lock demo?
A Hall sensor only unlocks a model box latch when a magnet is held on the right spot with the right pole facing it. A learning demo, not a real lock. You need Arduino Nano, Hall Effect Sensor A3144, SG90 Micro Servo, Resistor 10 kΩ, LED 5 mm red, LED 5 mm green, Resistor 220 Ω × 2, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 120 minutes.
- Level
- Beginner
- Time
- About 120 min
- Parts
- 9
Parts list
- Development BoardsBuyArduino Nano × 1
- SensorsBuy
- Motors & ActuatorsBuySG90 Micro Servo × 1
- PassivesBuyResistor 10 kΩ × 1
- SemiconductorsBuyLED 5 mm red × 1
- SemiconductorsBuyLED 5 mm green × 1
- PassivesBuyResistor 220 Ω × 2
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| A3144 pin 1 (VCC) | Nano 5V | Sensor power, flat face toward you, legs down, pin 1 on the left |
| A3144 pin 2 (GND) | Nano GND | Common ground |
| A3144 pin 3 (OUT) | Nano D2 | Open-collector output, low near the right pole |
| A3144 pin 3 (OUT) | 10 kilohm resistor to Nano 5V | Pull-up so the output reads high without a magnet |
| Servo signal (orange) | Nano D9 | Latch movement |
| Servo power (red) and ground (brown) | Nano 5V and GND | Small unloaded servo only |
| Red LED anode | 220 ohm to Nano D4 | Locked indicator, cathode to GND |
| Green LED anode | 220 ohm to Nano D5 | Unlocked indicator, cathode to GND |
Code
A Hall sensor changes its output when a magnetic field of the right polarity passes near it, so it can detect a magnet without any contact. The A3144 is a unipolar switch: its output goes low only when the south pole of a magnet faces the marked face of the chip, and the other pole does nothing. That makes the magnet the key: the right magnet, the right way round, in the right place. The output is open-collector, so a 10 kilohm resistor pulls it high when no magnet is present. The sketch confirms the magnet is present for a short time to avoid false triggers, then moves the servo latch to the unlocked position, turns the red LED off and the green LED on. After ten seconds it relocks automatically. A small servo can be run from the 5 volt pin while unloaded, but a stalled servo can pull enough current to reset the board, so keep the latch light. This is a teaching model: anyone with a spare magnet can open it, so never use a design like this to protect anything valuable, and keep strong magnets away from cards, phones and pacemakers.
Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
#include <Servo.h>
const int HALL = 2, SERVO_PIN = 9, LED_RED = 4, LED_GRN = 5;
const int LOCKED_ANGLE = 0, UNLOCKED_ANGLE = 90;
const unsigned long RELOCK_MS = 10000UL; // relock after ten seconds
const unsigned long CONFIRM_MS = 60; // magnet must be steady this long
Servo latch;
bool unlocked = false;
unsigned long unlockedAt = 0, seenSince = 0;
bool magnetWas = false;
void setLocked(bool lockIt) {
unlocked = !lockIt;
latch.write(lockIt ? LOCKED_ANGLE : UNLOCKED_ANGLE);
digitalWrite(LED_RED, lockIt);
digitalWrite(LED_GRN, !lockIt);
Serial.println(lockIt ? "Locked" : "Unlocked");
}
void setup() {
pinMode(HALL, INPUT); // external 10 kilohm pull-up
pinMode(LED_RED, OUTPUT);
pinMode(LED_GRN, OUTPUT);
latch.attach(SERVO_PIN);
Serial.begin(9600);
setLocked(true);
}
void loop() {
bool magnet = (digitalRead(HALL) == LOW); // A3144 pulls low near its marked pole
if (magnet && !magnetWas) seenSince = millis();
magnetWas = magnet;
if (!unlocked && magnet && millis() - seenSince >= CONFIRM_MS) {
setLocked(false);
unlockedAt = millis();
}
if (unlocked && millis() - unlockedAt >= RELOCK_MS) {
setLocked(true);
}
}What the serial monitor should show
Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.
Locked Unlocked
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Power on | Red LED on, latch locked |
| Right pole near the marked face | Green LED, latch opens |
| Wrong pole | No change |
| Wait ten seconds | Relocks and the red LED returns |
| Serial monitor | Locked and Unlocked messages |
If it does not work
Never unlocks
Try the other pole, and check the 10 kilohm pull-up to 5V.
Always unlocked
A magnet is nearby, or the sensor is wired backwards.
Servo twitches
Power the servo from a separate 5 V supply with a shared ground.
Board resets when the latch moves
The servo is stalled on the box, ease the latch.
Output reads low all the time
Check pin 1 and pin 2 are not swapped.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the magnet-key lock demo?
Arduino Nano, Hall Effect Sensor A3144, SG90 Micro Servo, Resistor 10 kΩ, LED 5 mm red, LED 5 mm green, Resistor 220 Ω × 2, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.
How long does the magnet-key lock demo take to build?
About 120 minutes for a beginner maker, in 8 steps.
How do I know the magnet-key lock demo works?
Power on: Red LED on, latch locked. Right pole near the marked face: Green LED, latch opens. Wrong pole: No change.
Never unlocks: what should I check?
Try the other pole, and check the 10 kilohm pull-up to 5V.
Always unlocked: what should I check?
A magnet is nearby, or the sensor is wired backwards.
Servo twitches: what should I check?
Power the servo from a separate 5 V supply with a shared ground.
Board resets when the latch moves: what should I check?
The servo is stalled on the box, ease the latch.
