Projects / Garden hose water usage meter

Garden hose water usage meter

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANOHelloPCF8574

    Install the library

    Search for LiquidCrystal I2C in the Library Manager.

  2. NANO

    Wire the sensor

    Red to 5V, black to GND, yellow to D2.

  3. NANOHelloPCF8574

    Wire the LCD and button

    SDA and SCL to A4 and A5, button D3 to GND.

  4. NANO

    Upload the sketch

    Display shows This: 0.00 L.

  5. NANO

    Blow gently through the sensor

    The pulse count rises a little.

  6. NANO

    Fill a 10 litre bucket through the sensor

    Note the litres shown.

  7. NANO

    Adjust PULSES_PER_LITRE

    Scale it by the true litres over the shown litres.

  8. NANO

    Fit it on the hose

    Use hose adapters and check for leaks.

In short

How do you build a garden hose water usage meter?

A flow sensor on a hose counts litres used each watering and shows the running total on an LCD. You need Arduino Nano, Water flow sensor YF-S201, 16x2 LCD with I2C backpack (PCF8574), Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Flow sensor red and blackNano 5V and GNDPower for the sensor
Flow sensor yellowNano D2Pulse output, interrupt pin
LCD I2C SDA and SCLNano A4 and A5Display, address 0x27
LCD I2C VCC and GNDNano 5V and GNDDisplay power
Reset buttonNano D3 to GNDShort press clears this watering, hold clears the total

Code

The YF-S201 has a small turbine with a magnet inside, and a Hall sensor makes one pulse for each turn. About 450 pulses mean one litre, or 7.5 pulses per second for each litre per minute of flow, but each sensor differs by several percent. Calibrate yours by filling a 10 litre bucket and adjusting PULSES_PER_LITRE until the display agrees. The pulse is counted by an interrupt so none are missed, and once a second the sketch turns the new pulses into litres and a flow rate in litres per minute. A short press clears the volume for this watering and a two-second hold clears the running total. The sensor is plastic with threaded ends, usually G1/2, so you need hose adapters, and it must not be used on mains-pressure lines over its rating, which is about 1.75 MPa for the body but best kept under 0.8 MPa in practice. Mount it with the arrow pointing in the flow direction and keep the electronics out of the wet. The total is not saved when power is lost.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <LiquidCrystal_I2C.h>

LiquidCrystal_I2C lcd(0x27, 16, 2);          // try 0x3F if the screen stays blank

const uint8_t PIN_FLOW = 2, BTN = 3;
const float PULSES_PER_LITRE = 450.0;        // typical for YF-S201, calibrate with a bucket

volatile unsigned long pulses = 0;
unsigned long lastPulses = 0;
unsigned long lastCalc = 0;
float thisLitres = 0, totalLitres = 0, flowLpm = 0;
unsigned long btnDownAt = 0;

void onPulse() { pulses++; }

void draw() {
  lcd.setCursor(0, 0);
  lcd.print("This: ");
  lcd.print(thisLitres, 2);
  lcd.print(" L    ");
  lcd.setCursor(0, 1);
  lcd.print("Tot ");
  lcd.print(totalLitres, 1);
  lcd.print(" ");
  lcd.print(flowLpm, 1);
  lcd.print("L/m   ");
}

void setup() {
  pinMode(PIN_FLOW, INPUT_PULLUP);
  pinMode(BTN, INPUT_PULLUP);
  attachInterrupt(digitalPinToInterrupt(PIN_FLOW), onPulse, RISING);
  lcd.init(); lcd.backlight();
  draw();
}

void loop() {
  if (millis() - lastCalc >= 1000) {
    unsigned long now = millis();
    noInterrupts(); unsigned long p = pulses; interrupts();
    unsigned long delta = p - lastPulses;
    lastPulses = p;
    float litres = delta / PULSES_PER_LITRE;
    thisLitres += litres;
    totalLitres += litres;
    flowLpm = litres * 60.0 * 1000.0 / (now - lastCalc);   // litres per minute
    lastCalc = now;
    draw();
  }

  if (digitalRead(BTN) == LOW) {
    if (btnDownAt == 0) btnDownAt = millis();
    if (millis() - btnDownAt > 2000) { totalLitres = 0; thisLitres = 0; btnDownAt = millis() + 100000UL; }
  } else {
    if (btnDownAt != 0 && millis() - btnDownAt < 2000) thisLitres = 0;   // short press
    btnDownAt = 0;
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No flow0.00 L and 0.0 L/m
10 litres into a bucketAbout 10 L after calibration
Short pressThis watering returns to zero
Two-second pressTotal returns to zero
Higher flowLarger L/m reading

If it does not work

Nothing counts

Check the yellow wire is on D2 and the arrow matches the flow.

Reading is wrong by a fixed percent

Calibrate with a bucket.

LCD blank

Try address 0x3F, or turn the contrast screw.

Count jumps when the pump starts

Move the sensor wire away from the pump motor.

Leaks at the sensor

Use thread tape on the adapters and do not overtighten the plastic.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the garden hose water usage meter?

Arduino Nano, Water flow sensor YF-S201, 16x2 LCD with I2C backpack (PCF8574), Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the garden hose water usage meter take to build?

About 90 minutes for a beginner maker, in 8 steps.

How do I know the garden hose water usage meter works?

No flow: 0.00 L and 0.0 L/m. 10 litres into a bucket: About 10 L after calibration. Short press: This watering returns to zero.

Nothing counts: what should I check?

Check the yellow wire is on D2 and the arrow matches the flow.

Reading is wrong by a fixed percent: what should I check?

Calibrate with a bucket.

LCD blank: what should I check?

Try address 0x3F, or turn the contrast screw.

Count jumps when the pump starts: what should I check?

Move the sensor wire away from the pump motor.