Projects / Walking cadence trainer

Walking cadence trainer

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ESP32

    Test the sensor

    Print the acceleration when you walk.

  2. ESP32

    Detect steps

    Print a line for each heel strike.

  3. ESP32

    Work out the cadence

    Average the last five intervals.

  4. ESP32

    Check with a count

    Walk 20 steps and compare.

  5. ESP32

    Add the cue

    Tick at the target rhythm.

  6. ESP32

    Add the button

    Switch measure and cue.

  7. ESP32

    Make the clip

    Fit it on the shoe.

In short

How do you build a walking cadence trainer?

A shoe clip measures steps per minute and beeps a rhythm to help with rehabilitation walking. You need Seeed XIAO ESP32C3, LIS3DH accelerometer, Passive buzzer, Li-Po battery 3.7 V 500 mAh and Tactile push button 6 mm. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LIS3DH VCC and GNDXIAO 3V3 and GNDPower
LIS3DH SDA and SCLXIAO D4 and D5I2C
Passive buzzer plusXIAO D1Cue tone
Passive buzzer minusXIAO GNDGround
ButtonXIAO D2 and GNDSwitch between measure and cue
LiPoXIAO BAT padsPower and charging

Code

The clip on the shoe detects each heel strike as a sharp peak and works out steps per minute from the last five steps. Press the button to switch to cue mode, which ticks at the target rhythm so a walker can match each step to the beat; rhythmic cues are used in some walking rehabilitation. This is a hobby aid, not a medical device. Any target rhythm and any rehabilitation exercise should be set by a physiotherapist or doctor who knows the person, and walking should stop at once if it causes pain or imbalance. The beep is a short, quiet tick; keep the volume low and do not use headphones near traffic. Mount the clip securely on the laces or the side of the shoe so that it does not rub or come loose, and keep the LiPo in a protected pouch, never worn while charging. Arduino IDE with the ESP32 boards package, board "XIAO_ESP32C3".

Runs on a virtual Seeed XIAO ESP32-C3 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Walking cadence trainer: measure steps per minute, or beep a target rhythm. Library: Adafruit LIS3DH. Board: XIAO ESP32C3.
#include <Wire.h>
#include <Adafruit_LIS3DH.h>

Adafruit_LIS3DH lis;
const int BUZZ = D1, BTN = D2;
int targetSpm = 100;                            // target steps per minute, set with your physiotherapist or trainer
bool cueMode = false;
float filt = 0, base = 9.8; bool above = false;
unsigned long lastStep = 0, lastBeep = 0, lastBtn = 0, intervals[5]; int idx = 0, nInt = 0;

void setup() {
  pinMode(BTN, INPUT_PULLUP);
  Wire.begin();
  lis.begin(0x18);
  lis.setRange(LIS3DH_RANGE_8_G);
  Serial.begin(115200);
}

float cadence() {                               // average of the last 5 step intervals
  if (nInt < 3) return 0;
  unsigned long s = 0; for (int i = 0; i < nInt; i++) s += intervals[i];
  return 60000.0 / (s / (float)nInt);
}

void loop() {
  if (!digitalRead(BTN) && millis() - lastBtn > 400) { cueMode = !cueMode; lastBtn = millis(); tone(BUZZ, cueMode ? 1800 : 900, 150); }

  sensors_event_t e; lis.getEvent(&e);
  float mag = sqrt(e.acceleration.x * e.acceleration.x + e.acceleration.y * e.acceleration.y + e.acceleration.z * e.acceleration.z);
  filt += (mag - filt) * 0.4; base += (filt - base) * 0.01;
  float swing = filt - base;
  if (!above && swing > 4.0 && millis() - lastStep > 300) {     // heel strike
    above = true;
    unsigned long dt = millis() - lastStep; lastStep = millis();
    if (dt < 2000) { intervals[idx] = dt; idx = (idx + 1) % 5; if (nInt < 5) nInt++; } else { nInt = 0; idx = 0; }   // long gap: start again
    Serial.print("Cadence "); Serial.print(cadence(), 0); Serial.println(" steps per minute");
  }
  if (above && swing < 1.5) above = false;

  if (cueMode && millis() - lastBeep >= 60000UL / targetSpm) { tone(BUZZ, 1500, 40); lastBeep = millis(); }   // a short tick at the target rhythm
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Walk steadilyCadence close to your real count
Stand still for 2 secondsStarts again on the next step
Cue modeEven ticks at the target rate
Change the targetTick rate follows

If it does not work

Counts too many steps

Raise the swing threshold or the minimum time.

Misses steps

Lower the threshold or move the clip to the heel side.

No ticks

Check the buzzer pin and that it is passive.

Cadence jumps

Average over more steps.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the walking cadence trainer?

Seeed XIAO ESP32C3, LIS3DH accelerometer, Passive buzzer, Li-Po battery 3.7 V 500 mAh and Tactile push button 6 mm.

How long does the walking cadence trainer take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the walking cadence trainer works?

Walk steadily: Cadence close to your real count. Stand still for 2 seconds: Starts again on the next step. Cue mode: Even ticks at the target rate.

Counts too many steps: what should I check?

Raise the swing threshold or the minimum time.

Misses steps: what should I check?

Lower the threshold or move the clip to the heel side.

No ticks: what should I check?

Check the buzzer pin and that it is passive.

Cadence jumps: what should I check?

Average over more steps.