Projects / Pressure pad door chime

Pressure pad door chime

Beginner2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANOFSR402

    Wire the divider

    FSR from 5V to A0, 10 kilohm from A0 to GND.

  2. NANO

    Wire the buzzer

    Plus to D6, minus to GND.

  3. NANO

    Upload the sketch

    Serial monitor shows readings near 0 with no load.

  4. NANO

    Press the pad with a finger

    The reading rises well above 300.

  5. NANO

    Release it

    The reading falls back to near 0.

  6. NANO

    Press again after three seconds

    The buzzer gives a double chime.

  7. NANOFSR402

    Change THRESHOLD

    Lower values make the pad more sensitive.

  8. NANO

    Place it under a mat

    Step on it to test the real setup.

In short

How do you build a pressure pad door chime?

A force-sensing pad under a mat triggers a chime when someone steps on it. You need Arduino Nano, Force sensitive resistor FSR 402, Resistor 10 kΩ, Active buzzer 5 V and Breadboard 830 Tie Points. It takes 8 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Nano 5VOne leg of the FSRTop of the divider
Other FSR legNano A0 and one end of 10 kilohmDivider midpoint
Other end of 10 kilohmNano GNDBottom of the divider
Active buzzer plusNano D6Chime output
Active buzzer minusNano GNDGround

Code

A force-sensitive resistor lowers its resistance as you press harder, from a few megohms with no load to a few kilohms under a firm press. With a 10 kilohm resistor to ground it forms a voltage divider, so the voltage on A0 rises with force. The sketch averages eight readings to ignore noise, compares the result to a threshold and chimes once on each new press. A lock-out of three seconds stops repeated chimes while someone stands on the pad. The FSR is better at telling that something is pressed than at measuring weight, because its readings drift and vary between parts. For a door mat, place the sensor under a thin rubber mat with a flat piece of card above it to spread the force over the small sensing circle, and fix it so it cannot fold. Keep the thin legs away from sharp bends. This is a convenience chime, not a security alarm.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const int FSR_PIN = A0;
const int BUZZER = 6;
const int THRESHOLD = 300;          // 0 to 1023, raise it if the pad triggers too easily
const unsigned long LOCKOUT_MS = 3000;

unsigned long lastChime = 0;
bool wasPressed = false;

int readSmooth() {
  long sum = 0;
  for (int i = 0; i < 8; i++) { sum += analogRead(FSR_PIN); delay(2); }
  return sum / 8;
}

void setup() {
  pinMode(BUZZER, OUTPUT);
  digitalWrite(BUZZER, LOW);
  Serial.begin(9600);
}

void loop() {
  int v = readSmooth();
  bool pressed = v > THRESHOLD;
  // Chime once per step, and not again until the lock-out time has passed
  if (pressed && !wasPressed && millis() - lastChime > LOCKOUT_MS) {
    digitalWrite(BUZZER, HIGH); delay(150);
    digitalWrite(BUZZER, LOW);  delay(100);
    digitalWrite(BUZZER, HIGH); delay(150);
    digitalWrite(BUZZER, LOW);
    lastChime = millis();
  }
  wasPressed = pressed;
  Serial.println(v);
  delay(30);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

512
511
512
511
512
511

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No loadReading under 50
Light finger pressReading rises
Firm pressReading above 500
Step on twice quicklyOne chime then a pause
Release and waitChime again on the next press

If it does not work

Always chimes

Raise THRESHOLD or check the 10 kilohm resistor is to GND.

Never chimes

Lower THRESHOLD and check the FSR legs are in the right rows.

Readings jump around

Add a 100 nanofarad capacitor from A0 to GND.

Buzzer stays on

Check its wiring and that it is an active buzzer.

Pad stops working

The thin legs may have been bent, replace the sensor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pressure pad door chime?

Arduino Nano, Force sensitive resistor FSR 402, Resistor 10 kΩ, Active buzzer 5 V and Breadboard 830 Tie Points.

How long does the pressure pad door chime take to build?

About 120 minutes for a beginner maker, in 8 steps.

How do I know the pressure pad door chime works?

No load: Reading under 50. Light finger press: Reading rises. Firm press: Reading above 500.

Always chimes: what should I check?

Raise THRESHOLD or check the 10 kilohm resistor is to GND.

Never chimes: what should I check?

Lower THRESHOLD and check the FSR legs are in the right rows.

Readings jump around: what should I check?

Add a 100 nanofarad capacitor from A0 to GND.

Buzzer stays on: what should I check?

Check its wiring and that it is an active buzzer.