Projects / Floating input and pull-up lab

Floating input and pull-up lab

Read a button with no pull resistor and watch the value jump around as your hand moves near the wire, then add a pull-down and a pull-up and compare. It shows why every input needs a defined state.

Beginner40 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Step 1, floating

    Push a bare jumper wire into D2, and leave the other end free.

  2. NANO

    Read the counts

    In mode n the number jumps about as you wave your hand near the wire.

  3. NANO

    Step 2, pull-down

    Add 10 kilohms from D2 to GND and a button from D2 to 5V.

  4. NANO

    Read the counts

    Always 0 until you press, then 100.

  5. NANO

    Step 3, pull-up

    Swap to 10 kilohms from D2 to 5V and the button from D2 to GND.

  6. NANO

    Read the counts

    Always 100 until you press, then 0.

  7. NANO

    Step 4, built-in pull-up

    Remove the resistor, send u, keep the button to GND: the same result.

In short

How do you build a floating input and pull-up lab?

Read a button with no pull resistor and watch the value jump around as your hand moves near the wire, then add a pull-down and a pull-up and compare. It shows why every input needs a defined state. You need Arduino Nano, Tactile push button 6 mm, Resistor 10 kΩ × 2, LED 5 mm red, Resistor 220 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 40 minutes.

Level
Beginner
Time
About 40 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Test wireNano D2, other end loose or on the buttonThe input under test
Red LED long legNano D6 through a 220 ohm resistorMirrors what the pin reads
Red LED short legNano GNDCommon ground
Pull-down resistor (step 2)10 kilohms from D2 to GNDHolds the pin low until the button pushes it high
Pull-up resistor (step 3)10 kilohms from D2 to 5VHolds the pin high until the button pulls it low
ButtonBetween D2 and 5V (step 2) or D2 and GND (step 3)Changes the level

Code

A pin set as an input with nothing attached is floating. It picks up electrical noise from your hand, the mains wiring and the other wires, and it reads high or low at random, so the count of high readings in each hundred drifts about. A pull-down resistor to ground makes the pin read low until a button connects it to 5 V. A pull-up resistor to 5 V makes it read high until a button connects it to ground. The Nano also has a built-in pull-up that you switch on with INPUT_PULLUP, and that is the neatest choice for a button to ground. In the Serial Monitor at 9600 baud, send n for a plain input and u for the built-in pull-up and watch the counts change. The LED lights when most of the readings are high.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t INPUT_PIN = 2;
const uint8_t LED_PIN = 6;

char mode = 'n';        // n = INPUT, u = INPUT_PULLUP; change it from the Serial Monitor

void setMode(char m) {
  mode = m;
  pinMode(INPUT_PIN, m == 'u' ? INPUT_PULLUP : INPUT);
  Serial.print("Mode: ");
  Serial.println(m == 'u' ? "INPUT_PULLUP (the chip's own pull-up)" : "INPUT (no pull resistor inside)");
}

void setup() {
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);
  Serial.println("Send n for INPUT or u for INPUT_PULLUP");
  setMode('n');
}

void loop() {
  if (Serial.available()) {
    char c = Serial.read();
    if (c == 'n' || c == 'u') setMode(c);
  }

  int highs = 0;
  for (int i = 0; i < 100; i++) {
    if (digitalRead(INPUT_PIN) == HIGH) highs++;
    delay(2);
  }
  digitalWrite(LED_PIN, highs > 50);
  Serial.print("HIGH ");
  Serial.print(highs);
  Serial.println(" of 100");
  delay(300);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Send n for INPUT or u for INPUT_PULLUP
Mode: INPUT (no pull resistor inside)
HIGH 0 of 100

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Floating wire in mode nCounts jump between low and high
10 kilohm pull-down, no press0 of 100
10 kilohm pull-down, pressed100 of 100
10 kilohm pull-up, no press100 of 100
Built-in pull-up with a button to GND100 until pressed, then 0

If it does not work

Counts never change

Check the wire is in D2 and the code is in the right mode.

Floating reading looks steady

Touch the wire with a finger, it picks up more noise.

LED always off

Check its direction and that the LED is on D6.

Pressed shows no change

Check which side of the button goes to 5V or GND.

Monitor shows nothing

Set 9600 baud.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the floating input and pull-up lab?

Arduino Nano, Tactile push button 6 mm, Resistor 10 kΩ × 2, LED 5 mm red, Resistor 220 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the floating input and pull-up lab take to build?

About 40 minutes for a beginner maker, in 7 steps.

How do I know the floating input and pull-up lab works?

Floating wire in mode n: Counts jump between low and high. 10 kilohm pull-down, no press: 0 of 100. 10 kilohm pull-down, pressed: 100 of 100.

Counts never change: what should I check?

Check the wire is in D2 and the code is in the right mode.

Floating reading looks steady: what should I check?

Touch the wire with a finger, it picks up more noise.

LED always off: what should I check?

Check its direction and that the LED is on D6.

Pressed shows no change: what should I check?

Check which side of the button goes to 5V or GND.