Projects / Electronic dice with seven LEDs

Electronic dice with seven LEDs

Beginner45 minGuided buildReviewed

Build it step by step

0 of 5 done
  1. NANO18.5 mA

    Lay out the dots

    Place seven LEDs in the dice pattern: two columns of three plus one in the centre.

  2. NANO18.5 mA

    Wire each dot

    D2 to D8 through 330 Ω to each LED's long leg, in the order listed. Short legs to GND.

  3. NANO

    Add the button

    D12 to GND.

  4. NANO

    Upload and roll

    Press the button. The dots flicker, slow down and stop.

  5. NANO

    Check fairness

    Roll 60 times and tally the results. Each number should come up roughly 10 times.

In short

How do you build an electronic dice with seven LEDs?

Press the button and seven LEDs laid out like dice dots roll, slow down and stop on a random number from one to six. You need Arduino Nano, LED 5 mm red × 7, Resistor 330 Ω × 7, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 5 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LED layoutTop-left, top-right, middle-left, centre, middle-right, bottom-left, bottom-rightDice dots
Nano D2 to D8330 Ω and one LED each, cathodes to GNDSeven dots
ButtonNano D12 and GNDRoll

Code

Arduino IDE, board "Arduino Nano". No extra libraries.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Dots: 0 top-left, 1 top-right, 2 middle-left, 3 centre, 4 middle-right, 5 bottom-left, 6 bottom-right
const int PIN[7] = {2, 3, 4, 5, 6, 7, 8};
byte faces[7];               // bit i set = dot i lit

void show(int n) { for (int i = 0; i < 7; i++) digitalWrite(PIN[i], bitRead(faces[n], i)); }

void setup() {
  for (int p : PIN) pinMode(p, OUTPUT);
  pinMode(12, INPUT_PULLUP);
  faces[1] = 1 << 3;
  faces[2] = (1 << 0) | (1 << 6);
  faces[3] = (1 << 0) | (1 << 3) | (1 << 6);
  faces[4] = (1 << 0) | (1 << 1) | (1 << 5) | (1 << 6);
  faces[5] = faces[4] | (1 << 3);
  faces[6] = faces[4] | (1 << 2) | (1 << 4);
  randomSeed(analogRead(A0));
  show(6);
}

void loop() {
  if (digitalRead(12) == HIGH) return;
  int n = 1;
  for (int d = 30; d < 300; d += d / 5 + 5) {        // roll, slowing down
    n = random(1, 7); show(n); delay(d);
  }
  while (digitalRead(12) == LOW) {}
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power upShows six
Button pressAbout a second of rolling, then one face from 1 to 6
60 rolls talliedEach face between about 5 and 15 times

If it does not work

A face looks wrong

Two LEDs are swapped. Match each pin to its dot position.

Always the same first roll

Leave A0 unconnected for the random seed.

One dot never lights

Turn the LED round or check its resistor.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the electronic dice with seven LEDs?

Arduino Nano, LED 5 mm red × 7, Resistor 330 Ω × 7, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the electronic dice with seven LEDs take to build?

About 45 minutes for a beginner maker, in 5 steps.

How do I know the electronic dice with seven LEDs works?

Power up: Shows six. Button press: About a second of rolling, then one face from 1 to 6. 60 rolls tallied: Each face between about 5 and 15 times.

A face looks wrong: what should I check?

Two LEDs are swapped. Match each pin to its dot position.

Always the same first roll: what should I check?

Leave A0 unconnected for the random seed.

One dot never lights: what should I check?

Turn the LED round or check its resistor.