Build it step by step
0 of 7 doneWire the three resistors in parallel
Common top rail and common bottom rail.
Predict the currents
Work out each with the divider rule.
Break the 1 kilohm branch
Lift the top leg of that resistor out of the rail.
Put the meter in the gap
Red probe in the mA socket, one probe on the rail, one on the resistor leg.
Read the current
Note it, then restore the leg.
Repeat for the other two branches
One at a time.
Add them up
The three should add to the total current from the battery.
How do you build a current divider ammeter lab?
Split a current between three parallel resistors and measure each branch with the meter's current range, then compare with the current divider rule. You also learn why a meter in current mode goes in series and never across the supply. You need Resistor 1 kΩ, Resistor 2.2 kΩ, Resistor 4.7 kΩ, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 40 minutes.
- Level
- Beginner
- Time
- About 40 min
- Parts
- 8
Parts list
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 2.2 kΩ × 1
- PassivesBuyResistor 4.7 kΩ × 1
- Tools & InstrumentsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Battery plus (red lead) | The meter's mA socket, then to the top rail | The meter measures the current in series |
| Top rail | One leg of each of the three resistors | The three branches |
| Other legs of the three resistors | Bottom rail and battery minus | Common return |
| Meter dial | DC current, the 200 mA range or lower | Series measurement only |
No code needed
No code. Three resistors in parallel share the current in proportion to their conductance, which is one over the resistance. The total current is about 9 divided by the combined resistance of 600 ohms, which is 15 mA. The rule gives about 9 mA in the 1 kilohm branch, about 4.1 mA in the 2.2 kilohm branch and about 1.9 mA in the 4.7 kilohm branch, and the three add up to the total. To measure a branch current you must break that branch and put the meter in the gap, so the current flows through the meter. The meter in current mode has almost no resistance, so never connect it across the battery or across a resistor, which would blow its fuse and could damage the battery. Move the red probe back to the volts socket and the dial away from current when you have finished.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| 1 kilohm branch | About 9 mA |
| 2.2 kilohm branch | About 4.1 mA |
| 4.7 kilohm branch | About 1.9 mA |
| Sum of branches | About 15 mA |
| Meter across the battery in current mode | Never do this |
If it does not work
Meter reads zero
Check the red probe is in the mA socket and the fuse is good.
Values are a little low
The meter adds a small resistance, which lowers the current slightly.
Meter fuse blown
Replace it with the same type and rating, and keep the meter only in series.
Currents do not add up
A branch may be loose, so check each resistor leg.
Display shows OL
Choose a higher range.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the current divider ammeter lab?
Resistor 1 kΩ, Resistor 2.2 kΩ, Resistor 4.7 kΩ, Digital multimeter, 9 V battery, 9 V battery snap with DC jack, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the current divider ammeter lab take to build?
About 40 minutes for a beginner maker, in 7 steps.
How do I know the current divider ammeter lab works?
1 kilohm branch: About 9 mA. 2.2 kilohm branch: About 4.1 mA. 4.7 kilohm branch: About 1.9 mA.
Meter reads zero: what should I check?
Check the red probe is in the mA socket and the fuse is good.
Values are a little low: what should I check?
The meter adds a small resistance, which lowers the current slightly.
Meter fuse blown: what should I check?
Replace it with the same type and rating, and keep the meter only in series.
Currents do not add up: what should I check?
A branch may be loose, so check each resistor leg.
