Projects / Exam countdown timer

Exam countdown timer

Beginner45 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the display

    CLK to D2, DIO to D3, with 5V and GND.

  2. NANO

    Add the buttons

    Plus on D4, minus on D5, start/pause on D6, each to ground.

  3. NANO

    Add the buzzer

    Buzzer between D8 and ground.

  4. NANO

    Upload and set the time

    Press plus or minus to change the time in 5 minute steps.

  5. NANO

    Start

    Press start. The display counts down every second.

  6. NANO

    Check the alerts

    Use a short time such as 11 minutes and wait for the three beeps at 10 minutes and the flash at zero.

  7. NANO

    Pause and resume

    Press start again to pause and resume.

In short

How do you build an exam countdown timer?

A big 4-digit display counts down exam time and beeps at 10 minutes and at the end. You need Arduino Nano, TM1637 4-digit display, Tactile push button 6 mm × 3, Active buzzer 5 V, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data). It takes 7 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
TM1637 CLK and DIONano D2 and D3Display
TM1637 VCC and GNDNano 5V and GNDSupply
Plus buttonNano D4 and GNDAdd 5 minutes
Minus buttonNano D5 and GNDSubtract 5 minutes
Start/pause buttonNano D6 and GNDRun or pause
Buzzer + and -Nano D8 and GNDAlerts

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "TM1637" by Avishay Orpaz. The count uses millis() and adds exactly 1000 ms each second so it does not drift. A Nano's crystal is accurate to a few seconds a day, which is plenty for a three hour exam.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>

TM1637Display display(2, 3);
const byte PLUS = 4, MINUS = 5, RUN = 6, BUZZ = 8;
long secsLeft = 60L * 60L;                  // default one hour
bool running = false, warned = false;
unsigned long lastTick = 0;

void show() {
  int m = secsLeft / 60, s = secsLeft % 60;
  display.showNumberDecEx(m * 100 + s, 0b01000000, true);    // mm:ss
}

void beeps(byte n) { for (byte i = 0; i < n; i++) { digitalWrite(BUZZ, HIGH); delay(150); digitalWrite(BUZZ, LOW); delay(150); } }

void setup() {
  pinMode(PLUS, INPUT_PULLUP); pinMode(MINUS, INPUT_PULLUP); pinMode(RUN, INPUT_PULLUP);
  pinMode(BUZZ, OUTPUT);
  display.setBrightness(7);
  show();
}

void loop() {
  if (!running) {
    if (digitalRead(PLUS) == LOW)  { secsLeft = min(secsLeft + 300, 99L * 60); show(); delay(250); }
    if (digitalRead(MINUS) == LOW) { secsLeft = max(secsLeft - 300, 0L); show(); delay(250); }
  }
  if (digitalRead(RUN) == LOW) {
    running = !running; lastTick = millis(); delay(300);
  }
  if (running && millis() - lastTick >= 1000) {
    lastTick += 1000;
    if (secsLeft > 0) secsLeft--;
    show();
    if (secsLeft == 600 && !warned) { beeps(3); warned = true; }     // ten minutes left
    if (secsLeft == 0) {
      for (byte i = 0; i < 10; i++) { display.setBrightness(7, i % 2 == 0); display.showNumberDecEx(0, 0b01000000, true); beeps(1); }
      display.setBrightness(7, true);
      running = false;
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Set 90 minutesDisplay shows 90:00
RunningCounts down one second per second
At 10 minutes leftThree beeps once
At zeroFlashes and beeps

If it does not work

Time runs fast or slow

Do not use delay() long in the loop. Keep the main loop free.

Buttons ignored

The wiring is on the wrong pins or the buttons are bouncing. Check D4 to D6.

Display blank

CLK and DIO may be swapped.

Wrong digits

Use showNumberDecEx with the colon mask as in the code.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the exam countdown timer?

Arduino Nano, TM1637 4-digit display, Tactile push button 6 mm × 3, Active buzzer 5 V, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data).

How long does the exam countdown timer take to build?

About 45 minutes for a beginner maker, in 7 steps.

How do I know the exam countdown timer works?

Set 90 minutes: Display shows 90:00. Running: Counts down one second per second. At 10 minutes left: Three beeps once.

Time runs fast or slow: what should I check?

Do not use delay() long in the loop. Keep the main loop free.

Buttons ignored: what should I check?

The wiring is on the wrong pins or the buttons are bouncing. Check D4 to D6.

Display blank: what should I check?

CLK and DIO may be swapped.

Wrong digits: what should I check?

Use showNumberDecEx with the colon mask as in the code.