Projects / Chord arpeggio trainer

Chord arpeggio trainer

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the four buttons

    D2 to D5, each to GND.

  2. NANO

    Wire the passive buzzer

    Plus to D8, minus to GND.

  3. NANO

    Upload and open the serial monitor at 9600

    A prompt appears.

  4. NANO

    Hold button 1

    Three notes of C major play in turn.

  5. NANO

    Hold button 2

    C minor, with a lower middle note.

  6. NANO

    Try buttons 3 and 4

    G major and A minor.

  7. NANO

    Change NOTE_MS

    Speed up or slow down the arpeggio.

In short

How do you build a chord arpeggio trainer?

Four buttons each play the notes of a different chord one after another on a small passive buzzer, so you hear the difference between a major and a minor chord and learn which notes make them. You need Arduino Nano, Tactile push button 6 mm × 4, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Button 1 (C major)Nano D2 and GNDPressing joins D2 to ground
Button 2 (C minor)Nano D3 and GNDPressing joins D3 to ground
Button 3 (G major)Nano D4 and GNDPressing joins D4 to ground
Button 4 (A minor)Nano D5 and GNDPressing joins D5 to ground
Passive buzzer +Nano D8Tone output
Passive buzzer -Nano GNDReturn path

Code

A chord is three or more notes that sound well together. A major chord has a bright sound and a minor chord has a darker one, and the difference is only one note: the middle note of a minor chord is a little lower. The sketch holds four chords, each as three frequencies in hertz, and plays them one after another, an arpeggio, while a button is held. Play C major and then C minor and listen to just the middle note changing. Then try G major and A minor. A passive buzzer plays whatever frequency the Nano sends with tone, but it is not a very musical instrument, and it can be loud, so keep it a hand-span from your ear. Once it works, add a fifth chord of your own by looking up the three note frequencies, or change NOTE_MS to speed up and slow down the arpeggio.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t BUTTON_PINS[4] = {2, 3, 4, 5};
const uint8_t BUZZER_PIN = 8;
const char* NAMES[4] = {"C major", "C minor", "G major", "A minor"};

// three notes per chord, in hertz
const int CHORDS[4][3] = {
  {262, 330, 392},   // C4 E4 G4   C major
  {262, 311, 392},   // C4 Eb4 G4  C minor (the middle note drops a little)
  {196, 247, 294},   // G3 B3 D4   G major
  {220, 262, 330}    // A3 C4 E4   A minor
};
const unsigned long NOTE_MS = 250;

int lastChord = -1;
int step = 0;
unsigned long lastStep = 0;

void setup() {
  for (int i = 0; i < 4; i++) pinMode(BUTTON_PINS[i], INPUT_PULLUP);
  pinMode(BUZZER_PIN, OUTPUT);
  Serial.begin(9600);
  Serial.println("Hold a button to hear its chord, one note at a time.");
}

void loop() {
  int chord = -1;
  for (int i = 0; i < 4; i++) {
    if (digitalRead(BUTTON_PINS[i]) == LOW) { chord = i; break; }
  }
  if (chord < 0) {
    noTone(BUZZER_PIN);
    lastChord = -1;
    return;
  }
  if (chord != lastChord) {
    lastChord = chord;
    step = 0;
    lastStep = 0;
    Serial.println(NAMES[chord]);
  }
  if (millis() - lastStep >= NOTE_MS) {
    lastStep = millis();
    tone(BUZZER_PIN, CHORDS[chord][step]);
    step = (step + 1) % 3;
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Hold a button to hear its chord, one note at a time.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Button 1C, E, G repeating
Button 2C, E-flat, G, a darker sound
ReleaseThe sound stops at once
Serial monitorPrints the chord name when it changes
Two buttons togetherThe lower numbered chord plays

If it does not work

No sound

Check you have a passive buzzer, not an active one, and the pin is D8.

Constant buzz

An active buzzer ignores the pitch, swap in a passive one.

One chord never plays

Check its button wiring to GND.

Notes sound the same

Listen for the middle note moving, it is a small change.

Upload fails

Choose the Old Bootloader option.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the chord arpeggio trainer?

Arduino Nano, Tactile push button 6 mm × 4, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the chord arpeggio trainer take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the chord arpeggio trainer works?

Button 1: C, E, G repeating. Button 2: C, E-flat, G, a darker sound. Release: The sound stops at once.

No sound: what should I check?

Check you have a passive buzzer, not an active one, and the pin is D8.

Constant buzz: what should I check?

An active buzzer ignores the pitch, swap in a passive one.

One chord never plays: what should I check?

Check its button wiring to GND.

Notes sound the same: what should I check?

Listen for the middle note moving, it is a small change.