Projects / Carrom pocket score counter

Carrom pocket score counter

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Test one sensor

    The module's LED lights when something is in front of it. Drop a coin past it.

  2. NANO

    Mount the four sensors

    Fix one at each pocket pointing into the net, away from the board edge.

  3. NANO

    Wire the signals

    Pocket outputs to D2 to D5, buttons to D6 and D7.

  4. NANOHelloPCF8574

    Wire the LCD

    On A4 and A5.

  5. NANO

    Upload and play

    Choose a side with the side button. Each coin pocketed adds a point to that side.

  6. NANO

    Queen

    Press the queen button to add 3 points to the current side.

  7. NANO

    Tune the sensors

    Adjust trimmers so a coin always counts once.

In short

How do you build a carrom pocket score counter?

Sensors under each carrom pocket count coins as they fall and keep score for both sides. You need Arduino Nano, IR obstacle avoidance sensor module × 4, 16x2 LCD with I2C backpack (PCF8574), Tactile push button 6 mm × 2, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data). It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Pocket sensor 1 to 4 OUTNano D2 to D5Low when a coin passes
All sensors VCC and GNDNano 5V and GNDSupply
LCD SDA and SCLNano A4 and A5Display
Side buttonNano D6 and GNDSwitch between white and black
Queen buttonNano D7 and GNDAdd the queen bonus to the current side

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "LiquidCrystal I2C". Mount a sensor looking across the inside of each pocket net so a falling coin passes in front of it. The module's trimmer sets the range, so adjust it until a coin triggers it and the net itself does not. A coin pocketed by the wrong side can be removed by editing the score in code later, or by adding an undo button.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <LiquidCrystal_I2C.h>

LiquidCrystal_I2C lcd(0x27, 16, 2);
const byte POCKET[4] = {2, 3, 4, 5};
const byte SIDE = 6, QUEEN = 7;
unsigned long lastSeen[4] = {0, 0, 0, 0};
int score[2] = {0, 0};                      // 0 white, 1 black
byte side = 0;

void show() {
  lcd.setCursor(0, 0); lcd.print("White "); lcd.print(score[0]); lcd.print("   Black "); lcd.print(score[1]); lcd.print("   ");
  lcd.setCursor(0, 1); lcd.print("Playing: "); lcd.print(side == 0 ? "White" : "Black"); lcd.print("   ");
}

void setup() {
  for (byte i = 0; i < 4; i++) pinMode(POCKET[i], INPUT);
  pinMode(SIDE, INPUT_PULLUP); pinMode(QUEEN, INPUT_PULLUP);
  lcd.init(); lcd.backlight();
  show();
}

void loop() {
  for (byte i = 0; i < 4; i++) {
    if (digitalRead(POCKET[i]) == LOW && millis() - lastSeen[i] > 600) {   // one coin per pocket per 0.6 s
      lastSeen[i] = millis();
      score[side]++;
      show();
    }
  }
  if (digitalRead(SIDE) == LOW)  { side = !side; show(); delay(300); }
  if (digitalRead(QUEEN) == LOW) { score[side] += 3; show(); delay(300); }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Coin falls in a pocketScore rises by one for the chosen side
Press the side buttonThe next coins count for the other side
Queen buttonAdds three
Two coins in quick successionBoth counted if more than 0.6 s apart

If it does not work

Counts twice

Increase the lockout time or reduce sensor range.

Misses coins

Increase range or aim it across the pocket opening.

Counts when nothing falls

Ambient light or the net triggers it. Lower the sensitivity.

Wrong score

Add an undo button that subtracts a point.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the carrom pocket score counter?

Arduino Nano, IR obstacle avoidance sensor module × 4, 16x2 LCD with I2C backpack (PCF8574), Tactile push button 6 mm × 2, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data).

How long does the carrom pocket score counter take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the carrom pocket score counter works?

Coin falls in a pocket: Score rises by one for the chosen side. Press the side button: The next coins count for the other side. Queen button: Adds three.

Counts twice: what should I check?

Increase the lockout time or reduce sensor range.

Misses coins: what should I check?

Increase range or aim it across the pocket opening.

Counts when nothing falls: what should I check?

Ambient light or the net triggers it. Lower the sensitivity.

Wrong score: what should I check?

Add an undo button that subtracts a point.