Projects / Garage car door ajar alarm

Garage car door ajar alarm

Beginner30 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Fit the reed and magnet

    Reed on the frame and magnet on the door, so they touch when closed.

  2. NANO

    Wire the reed and snooze

    Reed to D2 and GND, button to D3 and GND.

  3. NANO

    Add the buzzer

    Buzzer between D8 and GND.

  4. NANO

    Test with a short limit

    Set OPEN_LIMIT to 10 seconds, upload and open the door.

  5. NANO

    Check snooze

    Press the button during the alarm. The sound stops for the snooze time.

  6. NANOUSBUSB

    Set real times

    Restore 5 minutes and 10 minutes, then power from a USB adapter.

In short

How do you build a garage car door ajar alarm?

A reed switch on a garage or car boot warns if it stays open for more than 5 minutes, with a snooze button. You need Arduino Nano, Door reed switch MC-38, Active buzzer 5 V, Tactile push button 6 mm, 5 V 2 A USB adapter, USB A to micro-USB cable (data) and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Reed switchNano D2 and GNDClosed (LOW) when the door is shut
Snooze buttonNano D3 and GNDSilence for 10 minutes
Buzzer +Nano D8Alarm
Buzzer -Nano GNDReturn
USB adapterNano USB port5 V supply

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). No libraries. For testing set OPEN_LIMIT to 10 seconds. A garage has mains, but this build uses only a USB adapter plugged into an existing socket, so no mains wiring is needed.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const byte REED = 2, SNOOZE = 3, BUZZ = 8;
const unsigned long OPEN_LIMIT = 5UL * 60UL * 1000UL;   // 5 minutes
const unsigned long SNOOZE_MS = 10UL * 60UL * 1000UL;   // 10 minutes
unsigned long openSince = 0, snoozeUntil = 0;

void setup() {
  pinMode(REED, INPUT_PULLUP);
  pinMode(SNOOZE, INPUT_PULLUP);
  pinMode(BUZZ, OUTPUT);
}

void loop() {
  bool open = digitalRead(REED) == HIGH;         // magnet away from the reed
  if (!open) { openSince = 0; digitalWrite(BUZZ, LOW); }
  else if (openSince == 0) openSince = millis();

  if (digitalRead(SNOOZE) == LOW) snoozeUntil = millis() + SNOOZE_MS;

  if (open && millis() - openSince > OPEN_LIMIT && millis() > snoozeUntil) {
    digitalWrite(BUZZ, (millis() / 500) % 4 == 0);          // a short beep every two seconds
  } else digitalWrite(BUZZ, LOW);
  delay(20);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Door closedSilent
Door open under 5 minutesSilent
Door open longerBeep every two seconds
Press snoozeSilent for 10 minutes

If it does not work

Alarm with the door closed

The magnet is too far from the reed switch.

Never beeps

OPEN_LIMIT is long or the reed switch wire is not on D2.

Beeps too quietly

Use an active buzzer with more volume or a small speaker driver.

Snooze ignored

Check the button wires to D3 and ground.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the garage car door ajar alarm?

Arduino Nano, Door reed switch MC-38, Active buzzer 5 V, Tactile push button 6 mm, 5 V 2 A USB adapter, USB A to micro-USB cable (data) and Jumper wires male to male (40 pcs, 20 cm).

How long does the garage car door ajar alarm take to build?

About 30 minutes for a beginner maker, in 6 steps.

How do I know the garage car door ajar alarm works?

Door closed: Silent. Door open under 5 minutes: Silent. Door open longer: Beep every two seconds.

Alarm with the door closed: what should I check?

The magnet is too far from the reed switch.

Never beeps: what should I check?

OPEN_LIMIT is long or the reed switch wire is not on D2.

Beeps too quietly: what should I check?

Use an active buzzer with more volume or a small speaker driver.

Snooze ignored: what should I check?

Check the button wires to D3 and ground.