Projects / Connector crimping practice

Connector crimping practice

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Set up the tools

    Right slot in the crimper.

  2. 4.98V

    Strip ten wires

    Same length each time.

  3. Crimp ten Dupont pins

    Inspect each one.

  4. 4.98V

    Insert into housings

    Click and tug.

  5. Pull test

    2 kg for 10 seconds.

  6. JST

    Make JST leads

    Check polarity and keying.

  7. FERRUL

    Make ferrules

    Neat ends for screw terminals.

In short

How do you build a connector crimping practice?

Make Dupont, JST and ferrule leads with the right crimper, and test them for pull and continuity. You need Crimping tool (Dupont / JST), Dupont connector housings and crimp pins kit, JST XH 2.54 mm connector kit, Ferrules kit (bootlace), Wire stripper and cutter and Digital multimeter. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Strip lengthAbout 3 mm for Dupont and JSTExposes the right amount of copper
Crimp pinWire tabs and insulation tabsTwo separate crimps
HousingPush until it clicksLocks the pin
Pull testHang a 2 kg weight for 10 secondsProves the crimp
ContinuityMeter on the beep rangeProves the connection
FerruleStrip 8 mm and crimpNeat screw-terminal ends

No code needed

This is a skills lab with no code. Dupont, JST XH and bootlace ferrules are the most common connectors in electronics, and a good crimp is stronger and more reliable than solder in a cable that moves. Strip the wire to the length on the card; too long and bare copper pokes out, too short and the crimp grips only insulation. Crimp the small wire tabs onto the copper and the larger tabs around the insulation with the correct slot of the tool. Push the pin into the housing until it clicks and test by tugging gently. Do a real pull test by hanging a weight from the lead, then check continuity with the meter. Cut off a finished connector and look inside to see how the metal grips the wire. Practise on offcuts until ten in a row pass. Use ferrules on low-voltage screw terminals as shown; any mains wiring belongs to a qualified electrician. Wear safety glasses when cutting wire, since clippings fly.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Pull testHolds with no slip
ContinuityBeeps with no flicker
HousingLocks with a click
Ten in a rowAll pass

If it does not work

Pin slips off

Use the right crimp slot and strip length.

Wire pulls out

The wire tabs missed the copper.

Housing will not click

Pin is upside down.

Intermittent beep

Recrimp with a fresh pin.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the connector crimping practice?

Crimping tool (Dupont / JST), Dupont connector housings and crimp pins kit, JST XH 2.54 mm connector kit, Ferrules kit (bootlace), Wire stripper and cutter and Digital multimeter.

How long does the connector crimping practice take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the connector crimping practice works?

Pull test: Holds with no slip. Continuity: Beeps with no flicker. Housing: Locks with a click.

Pin slips off: what should I check?

Use the right crimp slot and strip length.

Wire pulls out: what should I check?

The wire tabs missed the copper.

Housing will not click: what should I check?

Pin is upside down.

Intermittent beep: what should I check?

Recrimp with a fresh pin.