Build it step by step
0 of 4 doneLay out the keys
Put eight buttons in a row across the breadboard gap like piano keys, and the ninth apart.
Wire the keys
One side of each button to D2...D9 (and D12), the other side to the GND rail.
Wire the buzzer
D11 through 100 Ω to the buzzer plus, minus to GND.
Upload and play
Play C to C, then press the ninth button.
How do you build an eight-key buzzer piano?
Eight push buttons play the notes of one octave (C to C) on a passive buzzer, and a ninth button plays a short tune. You need Arduino Uno R3, Passive buzzer, Tactile push button 6 mm × 9, Resistor 100 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 4 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 6
Parts list
- Development BoardsBuyArduino Uno R3 × 1
- Motors & ActuatorsBuyPassive buzzer × 1
- SwitchesBuy
- PassivesBuyResistor 100 Ω × 1In series with the buzzer
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Buttons 1 to 8 | Uno D2 to D9, other side to GND | Notes C D E F G A B C |
| Button 9 | Uno D12 and GND | Play a tune |
| Uno D11 | 100 Ω to buzzer +, buzzer − to GND | Sound |
Code
Arduino IDE, board "Arduino Uno". tone() is built in. A passive buzzer is needed: an active buzzer only makes one fixed beep.
Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
const int KEYS[8] = {2, 3, 4, 5, 6, 7, 8, 9};
const int NOTES[8] = {262, 294, 330, 349, 392, 440, 494, 523}; // C4 to C5 in Hz
const int BUZZER = 11, SONG = 12;
// "Sa Re Ga Ma" warm-up: C D E F G F E D C
const int TUNE[] = {262, 294, 330, 349, 392, 349, 330, 294, 262};
void setup() {
for (int k : KEYS) pinMode(k, INPUT_PULLUP);
pinMode(SONG, INPUT_PULLUP);
}
void loop() {
for (int i = 0; i < 8; i++) {
if (digitalRead(KEYS[i]) == LOW) {
tone(BUZZER, NOTES[i]);
while (digitalRead(KEYS[i]) == LOW) {} // hold the note while pressed
noTone(BUZZER);
}
}
if (digitalRead(SONG) == LOW) {
for (int f : TUNE) { tone(BUZZER, f, 300); delay(350); }
}
}Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Button 1 | Low C (262 Hz) |
| Button 8 | High C, clearly an octave above button 1 |
| Ninth button | C D E F G F E D C |
| Holding a key | The note lasts as long as you hold it |
If it does not work
Only a click, no note
You have an active buzzer, or it is backwards. Use a passive one.
A key plays nothing
Check that button spans the breadboard gap and its pin number.
Notes sound out of tune
Small buzzers are not flat across frequencies. A small 8 Ω speaker with the 100 Ω sounds better.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the eight-key buzzer piano?
Arduino Uno R3, Passive buzzer, Tactile push button 6 mm × 9, Resistor 100 Ω, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). Resistor 100 Ω: In series with the buzzer.
How long does the eight-key buzzer piano take to build?
About 45 minutes for a beginner maker, in 4 steps.
How do I know the eight-key buzzer piano works?
Button 1: Low C (262 Hz). Button 8: High C, clearly an octave above button 1. Ninth button: C D E F G F E D C.
Only a click, no note: what should I check?
You have an active buzzer, or it is backwards. Use a passive one.
A key plays nothing: what should I check?
Check that button spans the breadboard gap and its pin number.
Notes sound out of tune: what should I check?
Small buzzers are not flat across frequencies. A small 8 Ω speaker with the 100 Ω sounds better.
