Projects / Active and passive buzzer tour

Active and passive buzzer tour

Beginner35 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the active buzzer

    Plus to D8, minus to GND.

  2. NANO

    Wire the passive buzzer

    Plus to D9, minus to GND.

  3. NANO

    Upload the sketch

    Open the Serial Monitor at 9600 baud.

  4. NANO

    Listen to step 1

    The active buzzer beeps.

  5. NANO

    Listen to step 2

    The passive buzzer only clicks.

  6. NANO

    Listen to step 3

    A rising scale from the passive buzzer.

  7. NANO

    Listen to step 4

    The active buzzer keeps its own pitch.

In short

How do you build an active and passive buzzer tour?

Drive an active and a passive buzzer from the same kind of pin and hear the difference: one beeps with a plain on or off, the other plays notes only when given a tone. You need Arduino Nano, Active buzzer 5 V, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 35 minutes.

Level
Beginner
Time
About 35 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Active buzzer plusNano D8Plain on or off drive
Active buzzer minusNano GNDCommon ground
Passive buzzer plusNano D9Needs a changing signal, driven with tone
Passive buzzer minusNano GNDCommon ground

Code

An active buzzer has a tiny oscillator inside, so power alone makes it sing at one fixed pitch. A passive buzzer is only a speaker element, so it needs a changing signal, which the Nano's tone function supplies at the pitch you ask for. The sketch plays the four cases in turn and describes each in the Serial Monitor at 9600 baud so you can match what you hear. A plain high on the passive buzzer gives only a click at the start and end, and a tone on an active buzzer does not change its pitch because the pitch is built in. Rules of thumb: use an active buzzer for a simple alarm beep and a passive buzzer when you want melodies or different alert tones. Small buzzers can be loud at close range, so keep them away from ears and turn down the sound by adding a small resistor in series if needed.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t ACTIVE_PIN = 8;
const uint8_t PASSIVE_PIN = 9;

void say(const char* text) {
  Serial.println(text);
}

void setup() {
  pinMode(ACTIVE_PIN, OUTPUT);
  pinMode(PASSIVE_PIN, OUTPUT);
  Serial.begin(9600);
}

void loop() {
  say("1. Active buzzer, plain HIGH for 300 ms: a beep with its own fixed pitch");
  digitalWrite(ACTIVE_PIN, HIGH);
  delay(300);
  digitalWrite(ACTIVE_PIN, LOW);
  delay(1000);

  say("2. Passive buzzer, plain HIGH for 300 ms: only a click at the start and the end");
  digitalWrite(PASSIVE_PIN, HIGH);
  delay(300);
  digitalWrite(PASSIVE_PIN, LOW);
  delay(1000);

  say("3. Passive buzzer with tone(): a note, and the pitch follows the number");
  int notes[] = { 262, 294, 330, 349, 392, 440, 494, 523 };   // C major scale
  for (int i = 0; i < 8; i++) {
    tone(PASSIVE_PIN, notes[i], 200);
    delay(250);
  }
  noTone(PASSIVE_PIN);
  delay(1000);

  say("4. Active buzzer with tone(): it still plays its own pitch, maybe choppy");
  tone(ACTIVE_PIN, 880, 400);
  delay(900);
  noTone(ACTIVE_PIN);
  delay(2000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

1. Active buzzer, plain HIGH for 300 ms: a beep with its own fixed pitch
2. Passive buzzer, plain HIGH for 300 ms: only a click at the start and the end
3. Passive buzzer with tone(): a note, and the pitch follows the number
4. Active buzzer with tone(): it still plays its own pitch, maybe choppy

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Active, plain onA steady beep
Passive, plain onClick only
Passive with toneA clear scale
Active with toneSame pitch, maybe rough
Turn the buzzers over and read the labelsOften the active one has a sticker or is sealed

If it does not work

No sound from either

Check the plus pin direction and the wires to D8 and D9.

Passive buzzer silent on the scale

It may actually be an active type, so compare with step 1.

Active buzzer clicks only

It may be a passive type.

Too loud

Add a 100 ohm resistor in series.

Serial text garbled

Set the monitor to 9600 baud.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the active and passive buzzer tour?

Arduino Nano, Active buzzer 5 V, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the active and passive buzzer tour take to build?

About 35 minutes for a beginner maker, in 7 steps.

How do I know the active and passive buzzer tour works?

Active, plain on: A steady beep. Passive, plain on: Click only. Passive with tone: A clear scale.

No sound from either: what should I check?

Check the plus pin direction and the wires to D8 and D9.

Passive buzzer silent on the scale: what should I check?

It may actually be an active type, so compare with step 1.

Active buzzer clicks only: what should I check?

It may be a passive type.

Too loud: what should I check?

Add a 100 ohm resistor in series.