Projects / Button contact bounce counter

Button contact bounce counter

Count how many times the Nano thinks a single button press happened, then compare with a version that waits a few milliseconds. You see contact bounce for yourself and learn why every button needs debouncing.

Beginner40 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire the button between D2 and GND

    The internal pull-up does the rest.

  2. NANO

    Upload and open the serial monitor at 115200

    The prompt line appears.

  3. NANO

    Press once

    Both counts print.

  4. NANO

    Press fifty times, evenly

    Compare raw and clean.

  5. NANO

    Change DEBOUNCE_MS to 5, then 50

    Upload and repeat.

  6. NANO

    Try a second button

    Note which bounces more.

In short

How do you build a button contact bounce counter?

Count how many times the Nano thinks a single button press happened, then compare with a version that waits a few milliseconds. You see contact bounce for yourself and learn why every button needs debouncing. You need Arduino Nano, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 40 minutes.

Level
Beginner
Time
About 40 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Button leg 1Nano D2Button input
Button leg 2Nano GNDPressing joins D2 to ground

Code

When the metal contacts inside a push button meet, they do not close cleanly. They bounce for a millisecond or two, and a fast board sees several presses where you made one. The sketch counts two things at once. The raw count adds one for every drop to ground it sees, bounces included. The clean count only adds one when the signal has stayed steady for the debounce time. It waits until things settle before printing, so serial printing does not hide the bounces. Press the button fifty times, as evenly as you can, and note both counts. Then change DEBOUNCE_MS to 0, 5, 20 and 50 and repeat. You should see the clean count match your presses at around ten to twenty milliseconds, and fall short of them if the wait is too long and you press quickly. Different buttons bounce differently, so try two.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t BUTTON_PIN = 2;
const unsigned long DEBOUNCE_MS = 20;      // try 0, 5, 20 and 50

bool lastRaw = HIGH;
bool lastStable = HIGH;
unsigned long lastChange = 0;
unsigned long rawCount = 0;                // every falling edge, bounces included
unsigned long cleanCount = 0;              // only edges that stayed put
bool changed = false;

void setup() {
  pinMode(BUTTON_PIN, INPUT_PULLUP);
  Serial.begin(115200);
  Serial.println("Press the button. raw = every edge, clean = after debounce.");
}

void loop() {
  bool r = digitalRead(BUTTON_PIN);
  if (r != lastRaw) {                      // any change, including bounce
    lastRaw = r;
    lastChange = millis();
    if (r == LOW) rawCount++;
    changed = true;
  }
  if (millis() - lastChange > DEBOUNCE_MS && r != lastStable) {
    lastStable = r;
    if (r == LOW) cleanCount++;
    changed = true;
  }
  if (changed && millis() - lastChange > 150) {   // print once things have settled
    Serial.print("raw ");
    Serial.print(rawCount);
    Serial.print("   clean ");
    Serial.println(cleanCount);
    changed = false;
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Press the button. raw = every edge, clean = after debounce.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
One pressClean count rises by exactly one
Raw countOften higher than your presses
DEBOUNCE_MS 0Clean count is as wrong as raw
DEBOUNCE_MS 20Clean count matches your presses
DEBOUNCE_MS 50 with fast pressesSome presses are missed

If it does not work

Nothing prints

Set 115200 baud in the monitor.

Counts rise with no press

Check the button is wired to GND and D2 only.

Raw equals clean

Your button may be a clean one, try another.

Counts jump by two

Press and release evenly.

Upload fails

Choose the Old Bootloader option.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the button contact bounce counter?

Arduino Nano, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the button contact bounce counter take to build?

About 40 minutes for a beginner maker, in 6 steps.

How do I know the button contact bounce counter works?

One press: Clean count rises by exactly one. Raw count: Often higher than your presses. DEBOUNCE_MS 0: Clean count is as wrong as raw.

Nothing prints: what should I check?

Set 115200 baud in the monitor.

Counts rise with no press: what should I check?

Check the button is wired to GND and D2 only.

Raw equals clean: what should I check?

Your button may be a clean one, try another.

Counts jump by two: what should I check?

Press and release evenly.