Projects / Portable Bluetooth speaker

Portable Bluetooth speaker

Beginner2.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. +TP4056

    Charge test

    Connect the cell and TP4056 and check the charge LED with a USB-C cable.

  2. +MT3608

    Set the boost

    Power the MT3608 from the cell and adjust to 5.0 V with a meter.

  3. Wire the audio

    Join the receiver outputs through resistors into the amplifier input.

  4. Pair

    Switch on, pair a phone and play music.

  5. TP4056ABS

    Fit the box

    Mount the speaker with a sealed back volume and a cut-out for the USB-C port.

  6. Check run time

    Play at medium volume and note the hours per charge.

In short

How do you build a portable Bluetooth speaker?

A Bluetooth receiver, a small class-D amplifier and one 18650 cell with a charger make a pocket speaker. You need Bluetooth audio receiver module (BT5.0), PAM8403 stereo amplifier module, Speaker 4 Ω 3 W, 18650 cell 2600 mAh (branded), Battery holder 18650 single, TP4056 module with protection (USB-C), MT3608 Boost Module, Slide switch SPDT (SS12D00), Resistor 1 kΩ × 2 and ABS project box (100 × 60 × 25 mm). It takes 6 steps and about 150 minutes.

Level
Beginner
Time
About 150 min
Parts
10

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
18650 cell in holderTP4056 module B+ and B-Battery side (use the protected module)
TP4056 OUT+Slide switch, then MT3608 VIN+Power switch
TP4056 OUT-MT3608 VIN-Ground
MT3608 VOUT+ (set to 5.0 V first)PAM8403 +5V and Bluetooth module VCCRegulated 5 V
MT3608 VOUT-PAM8403 GND and Bluetooth module GNDCommon ground
Bluetooth module L out1 kΩ resistor to PAM8403 L inputLeft mix
Bluetooth module R out1 kΩ resistor to PAM8403 L inputRight mix, joined with the left at the input
PAM8403 L+ and L-SpeakerBridge-tied output, not grounded

No code needed

No code. Use a TP4056 module with battery protection (the type with an extra DW01 chip) so the cell cannot be over-discharged, and a good-quality cell. Set the MT3608 to exactly 5.0 V on a multimeter before connecting the amplifier or receiver. Mixing left and right through two 1 kΩ resistors makes one mono signal for the single speaker. Charging while playing is fine. Never short the cell or leave it in a hot car, and never charge Li-ion cells unattended in the first few tests.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Switch onBluetooth module shows ready to pair
Phone pairedMusic plays from the speaker
USB-C plugged inCell charges while playing
Cell emptyProtection cuts the output instead of draining the cell

If it does not work

Hum or whine

Add a 470 µF capacitor on the 5 V rail and keep the audio wires away from the boost converter.

No sound

Check the resistors reach the amplifier input and the speaker leads are not grounded.

Resets when loud

The boost converter is weak. Use a larger module or lower volume.

Cell does not charge

Check the polarity and the module's input connection.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the portable Bluetooth speaker?

Bluetooth audio receiver module (BT5.0), PAM8403 stereo amplifier module, Speaker 4 Ω 3 W, 18650 cell 2600 mAh (branded), Battery holder 18650 single, TP4056 module with protection (USB-C), MT3608 Boost Module, Slide switch SPDT (SS12D00), Resistor 1 kΩ × 2 and ABS project box (100 × 60 × 25 mm).

How long does the portable Bluetooth speaker take to build?

About 150 minutes for a beginner maker, in 6 steps.

How do I know the portable Bluetooth speaker works?

Switch on: Bluetooth module shows ready to pair. Phone paired: Music plays from the speaker. USB-C plugged in: Cell charges while playing.

Hum or whine: what should I check?

Add a 470 µF capacitor on the 5 V rail and keep the audio wires away from the boost converter.

No sound: what should I check?

Check the resistors reach the amplifier input and the speaker leads are not grounded.

Resets when loud: what should I check?

The boost converter is weak. Use a larger module or lower volume.

Cell does not charge: what should I check?

Check the polarity and the module's input connection.