Build it step by step
0 of 6 doneBuild the monostable
Pin 8 and 4 to +5 V, pin 1 to GND, pin 5 to 10 nF to GND.
Add the trigger
Pin 2 pulled up with 10 kΩ and a button from pin 2 to GND.
Add the timing network
+5 V to the 100 kΩ pot and a fixed 10 kΩ in series, to pins 6 and 7 joined, and the capacitor from there to GND.
Add the relay driver
Output pin 3 through 10 kΩ to the BC547 base, collector to the relay IN.
Test with an LED on the relay's output
Press the button. The relay clicks on, then off after the delay.
Set times
Time the delay at three pot positions and compare with 1.1 × R × C.
How do you build a 555 delay timer with relay?
Press a button and a relay stays on for a set time of about 1 to 12 seconds, or up to two minutes with a larger capacitor, set with a pot. You need NE555 Timer IC, Relay Module 5V, Potentiometer 100 kΩ (linear), Electrolytic Capacitor 100 µF, Electrolytic capacitor 1000 µF, Resistor 10 kΩ × 3, Ceramic capacitor 10 nF, BC547 NPN transistor, Tactile push button 6 mm, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and 5 V 2 A USB adapter. It takes 6 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 12
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- InterfacesBuyRelay Module 5V × 1
- PassivesBuy
- PassivesBuy
- PassivesBuy
- PassivesBuyResistor 10 kΩ × 3
- PassivesBuy
- SemiconductorsBuy
- SwitchesBuy
- PrototypingBuy
- PrototypingBuy
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 5 V adapter + | 555 pins 8 and 4, relay module VCC | Supply |
| 5 V adapter - | 555 pin 1, relay module GND, BC547 emitter | Common ground |
| Pin 2 | 10 kΩ to 5 V, and button to GND | Trigger, pulled low by the button |
| Pot (100 kΩ) + 10 kΩ in series | 5 V to the timing node (pins 6 and 7) | Sets R |
| Timing capacitor 100 µF | Timing node (+) to GND (-) | Sets C |
| Pin 5 | 10 nF to GND | Decoupling |
| Pin 3 (output) | 10 kΩ to BC547 base | Drives the inverter |
| BC547 collector | Relay module IN | Pulls IN low to switch the relay on (active-low module) |
| Relay COM and NO | Low-voltage load such as a lamp or fan | Mains loads need a qualified electrician |
No code needed
No code. t = 1.1 × R × C. With 100 µF and R up to 110 kΩ (pot plus fixed resistor) the delay runs from about 1 to 12 seconds, and swapping in 1000 µF gives about 10 seconds to two minutes. Capacitor tolerance is wide, so expect the time to differ by 20 % or more. If your relay module is active-high, connect the 555 output to IN through 1 kΩ and leave out the BC547.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Pot at minimum | About 1 s |
| Pot at maximum | About 12 s |
| Press the button during timing | Nothing changes, the timer is not retriggerable |
| Swap to 1000 µF | Ten times longer |
If it does not work
Relay on at power up
The module is active-low and the BC547 is missing or wrong. Check the collector wiring.
Delay much longer than expected
Electrolytic capacitors have wide tolerance and leak. Try a new one.
Relay chatters
The supply sags when the relay switches. Add a 100 µF capacitor across the 5 V rail.
Never times out
Pin 7 is not tied to pin 6, so the capacitor never discharges.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the 555 delay timer with relay?
NE555 Timer IC, Relay Module 5V, Potentiometer 100 kΩ (linear), Electrolytic Capacitor 100 µF, Electrolytic capacitor 1000 µF, Resistor 10 kΩ × 3, Ceramic capacitor 10 nF, BC547 NPN transistor, Tactile push button 6 mm, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and 5 V 2 A USB adapter.
How long does the 555 delay timer with relay take to build?
About 45 minutes for a beginner maker, in 6 steps.
How do I know the 555 delay timer with relay works?
Pot at minimum: About 1 s. Pot at maximum: About 12 s. Press the button during timing: Nothing changes, the timer is not retriggerable.
Relay on at power up: what should I check?
The module is active-low and the BC547 is missing or wrong. Check the collector wiring.
Delay much longer than expected: what should I check?
Electrolytic capacitors have wide tolerance and leak. Try a new one.
Relay chatters: what should I check?
The supply sags when the relay switches. Add a 100 µF capacitor across the 5 V rail.
Never times out: what should I check?
Pin 7 is not tied to pin 6, so the capacitor never discharges.
