Projects / Reverse polarity protection demo

Reverse polarity protection demo

Beginner1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. Identify the diode

    The stripe marks the cathode end.

  2. 9.7 mA

    Build the circuit

    Battery plus to the diode, then 330 ohm, then LED, then battery minus.

  3. ++9.7 mA

    Check it lights

    LED on with the battery the right way round.

  4. Measure the drop

    Meter across the diode.

  5. +

    Swap the battery leads

    Only after the diode is in place.

  6. 9.8 mA

    Watch the LED

    It stays off and nothing gets hot.

  7. Change the diode

    Repeat with the other type.

  8. Fill in the table

    Compare the voltage drops.

In short

How do you build a reverse polarity protection demo?

Wire a battery backwards on purpose through a diode and see how a series diode protects a circuit, and what it costs in voltage. You need Schottky Diode 1N5819, Rectifier Diode 1N4007, LED 5 mm red, Resistor 330 Ω, 9 V battery, 9 V battery snap with DC jack, Digital multimeter and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery plusDiode anode (the end without the stripe)Through the snap lead
Diode cathode (stripe end)330 ohm resistorSeries resistor
330 ohm resistorLED anode (long leg)LED load
LED cathode (short leg)Battery minusCloses the circuit
Multimeter red probeDiode anodeMeasures the voltage across the diode
Multimeter black probeDiode cathodeSame measurement

Code

A diode lets current flow in one direction only, so putting one in series with the power supply protects a circuit against a battery connected the wrong way round. In this demo the diode sits between the battery and the LED circuit. With the battery the right way round the LED lights and the diode drops a small voltage; with the battery reversed the diode blocks and nothing happens, so nothing is damaged. The price is the voltage drop: a silicon diode like the 1N4007 loses about 0.7 volt, while a Schottky diode like the 1N5819 loses only about 0.3 volt, which matters on low-voltage batteries. Measure the voltage across each diode with a multimeter and fill in the table to see the difference. Always build the circuit with the diode in place before you try reversing the battery: an LED on its own can be damaged by even a brief reversed connection. The method suits small loads of up to about one amp. For bigger loads, designers use a MOSFET instead of a diode to avoid the voltage loss, which is a good topic for a later build.

No code. This is a measuring exercise with a build sheet.

Results table. Fill it in for each diode.

Diode          Battery correct: LED?   Voltage across diode   Battery reversed: LED?
1N5819         ____                    ____ V                 ____
1N4007         ____                    ____ V                 ____

Typical results at about 20 mA
1N5819 Schottky:  about 0.2 to 0.4 V drop
1N4007 silicon:   about 0.6 to 0.8 V drop

Rule of thumb for the LED current: (battery volts - diode drop - LED drop) / 330 ohm

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Battery correctLED on
Battery reversedLED off, no heat
1N5819 dropAbout 0.2 to 0.4 V
1N4007 dropAbout 0.6 to 0.8 V
Diode flippedLED never lights

If it does not work

LED never lights

The diode may be the wrong way round, check the stripe.

LED very dim

Check the resistor value and the battery voltage.

Diode drop reads zero

The meter probes are on the wrong points.

Diode warm

The load current is too high, check the resistor.

Reversed battery lit the LED

The diode is not in series with the battery, rebuild it.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the reverse polarity protection demo?

Schottky Diode 1N5819, Rectifier Diode 1N4007, LED 5 mm red, Resistor 330 Ω, 9 V battery, 9 V battery snap with DC jack, Digital multimeter and Breadboard 830 Tie Points.

How long does the reverse polarity protection demo take to build?

About 60 minutes for a beginner maker, in 8 steps.

How do I know the reverse polarity protection demo works?

Battery correct: LED on. Battery reversed: LED off, no heat. 1N5819 drop: About 0.2 to 0.4 V.

LED never lights: what should I check?

The diode may be the wrong way round, check the stripe.

LED very dim: what should I check?

Check the resistor value and the battery voltage.

Diode drop reads zero: what should I check?

The meter probes are on the wrong points.

Diode warm: what should I check?

The load current is too high, check the resistor.