Tools / MOSFET switch losses and gate drive

How to work out MOSFET switch losses and gate drive

A MOSFET wastes power in two ways: all the time while on (Rds(on)), and a little at every switch. Here are both, with your numbers.

Pcond = I² × Rds(on); tsw ≈ Qg ÷ Ig; Pgate = Qg × Vgs × f

Inputs

V
A
mΩ
V
V
nC
Ω
kHz

Results update as you type. Prefixes work: 4.7k, 100u, 10n.

Result
Total loss
344 mW
Conduction loss
200 mW
Switching loss
144 mW
Voltage drop
100 mV
Gate current peak
50 mA
Switch time
300 ns
Gate drive power
1.5 mW
Step by step

The working with your numbers

  1. Voltage across the MOSFET when onV = I × Rds(on) = 2 A × 50 mΩ = 100 mV
  2. Conduction lossP = I² × Rds(on) = 2² × 0.05 = 200 mW
  3. Peak gate currentIg = Vgs ÷ Rg = 5 ÷ 100 = 50 mAA microcontroller pin gives about 20 mA. More than that needs a gate driver.
  4. Time to move the gate charget ≈ Qg ÷ Ig = 15 nC ÷ 50 mA = 300 ns
  5. Switching loss (rise and fall)P ≈ ½ × Vs × I × (2t) × f = 0.5 × 12 × 2 × 600 ns × 20 kHz = 144 mWA first estimate, because the drain voltage and current overlap for about this long.
  6. Power the driver must supply to the gateP = Qg × Vgs × f = 15 nC × 5 V × 20 kHz = 1.5 mW

Does the answer make sense?

  • OK: 5 V is well above the 2 V threshold, so the channel is fully on.
  • Watch out: 50 mA is too much for a microcontroller pin (about 20 mA). Raise Rg or add a gate driver.
  • OK: Switching takes about 600 ns each cycle, against a period of 50,000 µs.
  • OK: The part dissipates 344 mW in total. Add a heatsink above about 1 W.

Pick a real part

  • Pick a logic-level MOSFET (Vgs(th) under 2 V, Rds(on) quoted at 4.5 V) for 3.3 V or 5 V drive, with a rating of at least 2 × 2 A.
  • Add a 10 kΩ resistor from gate to ground so it stays off while the microcontroller boots.
  • A flyback diode is needed across relays, motors and other coils.

Common mistakes

  • Using the datasheet's Rds(on) at 10 V when you drive at 3.3 V. It is much higher at a low drive.
  • Forgetting the gate resistor's job. Too small gives ringing and a big current spike, too large makes it switch slowly and hot.
  • Switching a motor with no flyback diode.

Learn it, try it, build it

Calculated, not measured. Check the exact part datasheet and your real circuit before powering anything.

Common questions

How do you work out the power a MOSFET dissipates?

Conduction loss is I² × Rds(on). 2 A through 50 mΩ gives 4 × 0.05 = 0.2 W. Add switching loss at higher frequencies, about ½ × V × I × (rise time + fall time) × f.

Why does a MOSFET get hot even with a low Rds(on)?

Either the gate drive is too low so the real Rds(on) is higher than the datasheet figure, or it switches slowly at a high frequency so the voltage and current overlap during each transition.