Lab / MSBTE / Analog and linear ICs / Experiment 4

Schmitt trigger using an op-amp

Analog and linear ICsVirtual readings4 viva questionsRecord book ready
Open virtual bench
Aim

To build an inverting Schmitt trigger and measure its upper and lower trip points and hysteresis.

Apparatus
  • IC 741
  • Resistors R1 10 kΩ, R2 2.2 kΩ
  • Dual supply ±12 V
  • Function generator
  • CRO
−+Vout = −Rf/Rin · Vin

Theory

A Schmitt trigger is a comparator with positive feedback. In the inverting version the reference at pin 3 is β·Vsat, with β = R2/(R1 + R2). The output switches low when the input rises above UTP = +β·Vsat and high again when it falls below LTP = −β·Vsat. The difference UTP − LTP is the hysteresis, which stops noisy inputs from causing many switchings.

Read the lesson: Logic levels ›
Circuit connections
  • Input → pin 2; R1 from pin 6 (output) to pin 3; R2 from pin 3 to ground

Procedure

Pre-lab check

4 questions · 75% to be ready
1What is hysteresis?
2Why use a Schmitt trigger?
3How is it different from a comparator?
4Name a digital IC with Schmitt inputs.

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
QuantityValue (V)
β = R2 / (R1 + R2)0.18
UTP1.89
LTP-1.89
Hysteresis3.79

Precautions

  • Use an input amplitude larger than UTP.
  • Use DC coupling for both channels.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.QuantityValue (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

UTP = ___ V, LTP = ___ V, hysteresis = ___ V, close to the calculated values.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What is hysteresis?
2. Why use a Schmitt trigger?
3. How is it different from a comparator?
4. Name a digital IC with Schmitt inputs.

Quick answers for your record and viva

What is the aim of the schmitt trigger using an op-amp experiment?

To build an inverting Schmitt trigger and measure its upper and lower trip points and hysteresis.

What apparatus is needed for schmitt trigger using an op-amp?

IC 741, Resistors R1 10 kΩ, R2 2.2 kΩ, Dual supply ±12 V, Function generator, CRO.

What is the theory behind schmitt trigger using an op-amp?

A Schmitt trigger is a comparator with positive feedback. In the inverting version the reference at pin 3 is β·Vsat, with β = R2/(R1 + R2). The output switches low when the input rises above UTP = +β·Vsat and high again when it falls below LTP = −β·Vsat. The difference UTP − LTP is the hysteresis, which stops noisy inputs from causing many switchings.

What result should I get in schmitt trigger using an op-amp?

UTP = ___ V, LTP = ___ V, hysteresis = ___ V, close to the calculated values.

What precautions should I take in schmitt trigger using an op-amp?

Use an input amplitude larger than UTP. Use DC coupling for both channels.

Schmitt trigger using an op-amp: lab experiment and viva