Lab / MSBTE

MSBTE lab

Maharashtra State Board of Technical Education · Maharashtra · lab lists checked against the published syllabus

Exp 1

Test the performance of PN Junction diode

SimViva 4Record
Exp 2

Test the performance of zener diode

SimViva 4Record
Exp 3

Check the performance of photo diode by varying the light intensity as well as the distance of the light source

Not on ElectroLark yet
Exp 4

Construct and Test the half wave rectifier

SimViva 4Record
Exp 5

Build and Test the half wave rectifier with LC filter/ π filter

SimViva 4Record
Exp 6

Prepare and Test the full wave rectifier using two diodes

SimViva 4Record
Exp 7

Build and Test the full wave Bridge rectifier on bread board

SimViva 4Record
Exp 8

Use LC/ π filter with full wave rectifier to measure ripple factor

SimViva 4Record
Exp 9

Construct and Test the full wave rectifier on bread board using IC KBU 808 with filter

SimViva 4Record
I = 13 mA
Exp 10

Build and Test the performance parameters of 7 Segment LED display FND 507/508

Not on ElectroLark yet
Av ≈ 48
Exp 11

Identify and select transistors using datasheets

Not on ElectroLark yet
Av ≈ 48
Exp 12

Build and Test the performance of BJT working in CB mode

SimViva 4Record
Av ≈ 48
Exp 13

Prepare and Test the performance of BJT working in CE mode

SimViva 4Record
Av ≈ 48
Exp 14

Build and Test the BJT voltage divider bias circuit for given input

SimViva 4Record
Av ≈ 48
Exp 15

Construct and Test the performance parameters of BJT as Switch

SimViva 4Record
Av ≈ 48
Exp 16

Build and Test the performance of single stage Low Power Common emitter amplifier

SimViva 4Record
Av ≈ 48
Exp 17

Simulate and Test output waveform and frequency response of single stage common emitter (CE) amplifier using simulation software

SimViva 4Record
Av ≈ 48
Exp 18

Build and Test the performance of RC coupled two stage amplifier

Not on ElectroLark yet
Av ≈ 48
Exp 19

Test the performance of FET drain characteristics

SimViva 4Record
Av ≈ 48
Exp 20

Check the performance of FET transfer characteristics and calculate transconductance

SimViva 4Record
Av ≈ 48
Exp 21

Build and Test the performance of common source FET amplifier

Not on ElectroLark yet
Exp 22

Test the various blocks of regulated dc power supply

SimViva 4Record
Exp 23

Find out faults at different stages of regulated dc power supply

SimViva 4Record
Exp 24

Trouble shoot given DC regulated power supply

SimViva 4Record
Exp 25

Construct and test the performance of Zener voltage regulator for given voltage

SimViva 4Record
Exp 26

Build and Test the performance of Positive voltage regulator using 78XX three terminal IC for given voltage

SimViva 4Record
Exp 27

Build and Test the performance of Negative voltage regulator using 79XX three terminal IC for given voltage

SimViva 4Record
Exp 28

Construct and test the performance of Dual voltage regulator using 78XX and 79XX three terminal IC for given voltage

SimViva 4Record
Exp 29

Build and Test the performance of LOW voltage regulator using IC LM723 for given voltage (2 V-7V)

Not on ElectroLark yet
Exp 30

Build and Test the performance of HIGH voltage regulator using IC LM723 for given voltage (7V-30V)

Not on ElectroLark yet

Source: MSBTE K scheme syllabus (copy at inspirenignite.com), checked 25 Oct 2026. Always confirm with your lab manual: colleges sometimes add or drop experiments.

Maker plan. Single experiments print free.

My syllabus is different, or not listed

Send your lab syllabus. One student's upload maps the lab for everyone at that university.

Common questions

Which electronics lab experiments are in the MSBTE syllabus?

This page lists 8 experiments for MSBTE, checked against the published lab syllabus, including V-I characteristics of a PN junction diode; Zener diode characteristics and voltage regulator; Half-wave and full-wave rectifiers with and without filter; BJT characteristics (CE, with CB and CC); Frequency response of a common-emitter amplifier; Light-activated relay (LDR and transistor).

How do I prepare for a MSBTE electronics lab practical?

Open each experiment before the lab: read the aim and theory, try the virtual readings so you know what to expect, do the pre-lab check and practise the viva questions. Practical exam practice draws a random experiment and runs a timer.