Lab / VTU / Analog and linear ICs / Experiment 10

4-bit R-2R ladder D/A converter

Analog and linear ICsVirtual readings4 viva questionsRecord book ready
Open virtual bench
Aim

To build a 4-bit R-2R ladder DAC with an op-amp and measure its output for every input code, its resolution and accuracy.

Apparatus
  • IC 741
  • Resistors 10 kΩ and 20 kΩ (1%)
  • Switches or an Arduino for the 4 bits
  • DC reference 5 V
  • Dual supply
  • Multimeter
ABY

Theory

Each bit switches its 2R leg to Vref (1) or ground (0). The ladder divides by 2 at each node, so the output of the inverting amplifier (Rf = R) is Vo = −Vref·(D/2ⁿ), where D is the binary input. Resolution is Vref/2ⁿ: the step for one count.

Circuit connections
  • R-2R ladder with 4 inputs (MSB nearest the op-amp); ladder end to pin 2; Rf = R from pin 2 to 6; pin 3 to ground

Procedure

Pre-lab check

4 questions · 75% to be ready
1Why only two resistor values in an R-2R ladder?
2Define resolution.
3What is settling time?
4How is an Arduino's PWM used as a DAC?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
Resolution312.5 mV per step
Full scale (1111)-4.6875 V
-5.06-3.7-2.34-0.980.3803.757.51115Code DVo (V)
CodeDVo theory (V)
000000
00011-0.3125
00102-0.625
00113-0.9375
01004-1.25
01015-1.5625
01106-1.875
01117-2.1875
10008-2.5
10019-2.8125
101010-3.125
101111-3.4375
110012-3.75
110113-4.0625
111014-4.375
111115-4.6875

Precautions

  • Use 1% resistors; mismatch shows up as missing or uneven steps.
  • Measure the reference voltage, do not assume it.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.CodeDVo theory (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

Step size = ___ mV (theory ___), maximum error = ___ mV.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. Why only two resistor values in an R-2R ladder?
2. Define resolution.
3. What is settling time?
4. How is an Arduino's PWM used as a DAC?

Quick answers for your record and viva

What is the aim of the 4-bit r-2r ladder d/a converter experiment?

To build a 4-bit R-2R ladder DAC with an op-amp and measure its output for every input code, its resolution and accuracy.

What apparatus is needed for 4-bit r-2r ladder d/a converter?

IC 741, Resistors 10 kΩ and 20 kΩ (1%), Switches or an Arduino for the 4 bits, DC reference 5 V, Dual supply, Multimeter.

What is the theory behind 4-bit r-2r ladder d/a converter?

Each bit switches its 2R leg to Vref (1) or ground (0). The ladder divides by 2 at each node, so the output of the inverting amplifier (Rf = R) is Vo = −Vref·(D/2ⁿ), where D is the binary input. Resolution is Vref/2ⁿ: the step for one count.

What result should I get in 4-bit r-2r ladder d/a converter?

Step size = ___ mV (theory ___), maximum error = ___ mV.

What precautions should I take in 4-bit r-2r ladder d/a converter?

Use 1% resistors; mismatch shows up as missing or uneven steps. Measure the reference voltage, do not assume it.

4-bit R-2R ladder D/A converter: lab experiment and viva