Wireless power transfer for charging
Phones, toothbrushes and electric buses all charge without plugs now. Building a resonant inductive link and measuring how efficiency falls with distance and misalignment teaches the physics behind it.
- Parts
- ₹2,650
- Build
- 13 weeks
- Board
- Arduino Nano
- Objectives
- 6
Block diagram
- Two INA219s and NanoMeasure input and output power
- Reference sensorGives the values the others are checked against+
- Oscillator and MOSFETsDrive the transmitter coil
- 12 V supplyFeeds the transmitter
- Transmitter and receiver coilsCouple power through the air
- Rectifier and regulatorGive a steady 5 V
- Data loggerStores timestamped readings for analysis+
Objectives
- To design and wind matched coils and resonate them at a calculated frequency.
- To transfer at least 5 W across 2 cm.
- To measure efficiency against distance (0 to 10 cm) and lateral misalignment.
- To compare resonant and non-resonant receivers.
- To log timestamped data and analyse it to support the conclusions with evidence.
- To calibrate two sensors against a reference and compare their accuracy and cost.
Parts and specifications
- Arduino Nano (CH340, Type-C)ATmega328P 16 MHz, 5 V logic, 8 analog inputs, small enough for wearables and helmets₹350Buy
- Enamelled copper wire 1 mm, 10 m₹250
- × 4Polypropylene capacitors 0.1 µF (resonant tank)₹60
- UF4007 fast diodes and 12 V Zeners for the driver₹40
- LM2596 buck converter4 to 40 V in, 1.25 to 37 V out, up to 2 A continuous (3 A peak), about 85% efficient₹90Buy
- Ruler stand for distance tests₹100
- DS3231 RTC moduleTemperature-compensated, ±2 ppm (about 1 minute a year), I²C 0x68, CR2032 backup₹150Buy
- Second sensor of another type₹250
Total about ₹2,650 at typical online prices. Tap a part for its pinout and datasheet notes.
Design calculations
L (µH) = (r² N²) / (9r + 10ℓ) with r and ℓ in inches. 10 turns, r = 1.5 in, ℓ = 0.4 in: L = 225 / 17.5 ≈ 12.9 µH.
f = 1 / (2π√(LC)). 12.9 µH with 0.4 µF (four 0.1 µF in parallel): f = 1 / (2π × √(5.16 × 10⁻¹²)) ≈ 70 kHz. Tune the receiver to the same frequency.
η = Pout / Pin from the two INA219s. Expect over 60% at 1 cm, falling sharply once the gap passes the coil radius.
Coupling k falls roughly with the cube of distance beyond the coil radius; resonance raises transfer for weak k (high Q).
Pin map
| Signal | Pin or connection |
|---|---|
| Driver | Royer (ZVS) oscillator: two IRFZ44N, gate resistors 470 Ω, 12 V Zeners, UF4007 cross diodes, centre-tapped transmitter coil |
| INA219 input / output | I²C 0x40 / 0x41 on Nano A4 / A5 |
| Receiver | Coil + tuning capacitor → bridge of four 1N5822 → 470 µF → LM2596 5 V |
| OLED | Same I²C bus |
Firmware outline
- Read input and output V and I every 200 ms, compute both powers and efficiency.
- Show them on the OLED with the distance entered by buttons.
- Log distance, offset and efficiency over serial for plotting.
- Measure the oscillator frequency with a pin interrupt (via a pickup loop and comparator) or a scope.
Test plan
| Test | Expected result |
|---|---|
| Gap 0 to 10 cm in 1 cm steps | Efficiency vs distance graph |
| Lateral offset 0 to 5 cm | Efficiency vs misalignment |
| Receiver tuned vs not tuned | Power compared |
| Driver temperature after 10 minutes | Heatsink adequate |
These rows start your results table when you plan the project.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 5.
Make it yours
One or two upgrades for a mini project, two to four for a major one.
Datasheets and sources to cite
- Kurs et al., Wireless power transfer via strongly coupled magnetic resonances (Science, 2007)
- Wireless Power Consortium Qi specification overview
- ICNIRP guidelines for magnetic field exposure
About this project
How much does the wireless power transfer for charging project cost?
About ₹1,790 for the parts in the base list: Arduino Nano (CH340, Type-C), 12 V 2 A DC adapter, IRFZ44N MOSFET × 2, Enamelled copper wire 1 mm, 10 m, Polypropylene capacitors 0.1 µF (resonant tank) × 4, UF4007 fast diodes and 12 V Zeners for the driver, 1N5822 Schottky diode × 4, 470 µF 35 V electrolytic × 2, LM2596 buck converter, INA219 current and power sensor × 2, 0.96 inch OLED (SSD1306, I²C), Ruler stand for distance tests.
How long does it take?
About 10 weeks for the base project, built on an Arduino Nano. Each upgrade adds time.
Which branches is it suitable for?
Electrical and Electronics, Electronics and Communication, as a mini or major project.
Which pins and design calculations does it use?
Driver on Royer (ZVS) oscillator: two IRFZ44N, gate resistors 470 Ω, 12 V Zeners, UF4007 cross diodes, centre-tapped transmitter coil; INA219 input / output on I²C 0x40 / 0x41 on Nano A4 / A5; Receiver on Coil + tuning capacitor → bridge of four 1N5822 → 470 µF → LM2596 5 V. Worked calculations on this page: coil inductance (air core, wheeler), resonant frequency, efficiency, coupling.
How do I test it?
Gap 0 to 10 cm in 1 cm steps: Efficiency vs distance graph. Lateral offset 0 to 5 cm: Efficiency vs misalignment. Receiver tuned vs not tuned: Power compared. Driver temperature after 10 minutes: Heatsink adequate.
What are the objectives?
To design and wind matched coils and resonate them at a calculated frequency. To transfer at least 5 W across 2 cm. To measure efficiency against distance (0 to 10 cm) and lateral misalignment. To compare resonant and non-resonant receivers.
