Solar-powered grass cutter with remote control
Petrol lawn mowers are noisy, polluting and costly to run for colleges, parks and farms. A small grass cutter that charges from a solar panel and is driven by phone shows electric drive design end to end.
- Parts
- ₹6,655
- Build
- 14 weeks
- Board
- ESP32
- Objectives
- 6
Block diagram
- Phone over BluetoothDrives the cutter
- Ultrasonic sensorStops before obstacles
- ESP32Controls drive and blade
- Solar panel and chargerCharges the pack
- 3S Li-ion packStores energy
- Solar power unitPanel, charger and cell that keep the node running+
- Drive motors and driverMove the cutter
- Blade motor and MOSFETCuts the grass
- Phone appShows readings and sends commands over Bluetooth+
Objectives
- To drive the cutter from a phone over Bluetooth.
- To cut grass with a guarded blade that stops in under 2 s when commanded or on an obstacle.
- To charge the pack from the solar panel and measure charge time.
- To measure area cut per charge and cost per year against a petrol mower.
- To monitor and control the system from a phone over Bluetooth.
- To power the system from a solar-charged battery and measure its energy budget.
Parts and specifications
- ESP32 DevKit V1Dual-core 240 MHz, 520 KB SRAM, Wi-Fi + Bluetooth, 3.3 V logic, 12-bit ADC (use ADC1 pins when Wi-Fi is on)₹450Buy
- CN3791 MPPT solar Li-ion charger (3S setting)₹450
- Johnson geared motor 300 RPM 12 V12 V, 300 RPM, about 10 kg·cm, 0.3 A no-load and up to 3 A stall₹900Buy
- 775 DC motor 12 V with blade and guard₹600
- HC-SR04 ultrasonic sensor2 cm to 4 m, 15° beam, 40 kHz, 10 µs trigger, echo pulse 58 µs per cm, 5 V₹80Buy
- LM2596 buck converter4 to 40 V in, 1.25 to 37 V out, up to 2 A continuous (3 A peak), about 85% efficient₹90Buy
- Chassis, wheels and blade guard₹900
- TP4056 charger with protection1 A CC/CV Li-ion charging to 4.2 V, DW01 protection cuts at about 2.5 V₹40Buy
- MT3608 boost converter (3.7 V to 5 V)2 to 24 V in, up to 28 V out, 2 A switch, for 3.7 V to 5 V₹50Buy
Total about ₹6,655 at typical online prices. Tap a part for its pinout and datasheet notes.
Design calculations
775 motor at 12 V about 2 A cutting = 24 W. Drive motors 2 × 0.6 A × 12 V ≈ 14 W. Total ≈ 38 W.
3S2P pack about 4 Ah × 11.1 V = 44 Wh; 80% usable = 35 Wh → about 55 minutes of cutting.
10 W panel gives about 7 W into the pack after losses; 35 Wh / 7 W = 5 hours of good sun (a full day's charge).
0.3 m cut width × 0.3 m/s × 3300 s ≈ 300 m² per charge, allowing for turns.
6000 RPM on a 20 cm blade: v = π × 0.2 × 100 rev/s ≈ 63 m/s, why the guard is essential.
Pin map
| Signal | Pin or connection |
|---|---|
| L298N ENA, IN1, IN2, IN3, IN4, ENB | GPIO 25, 26, 27, 14, 12, 33 |
| Blade MOSFET gate (via 100 Ω, 10 kΩ pull-down) | GPIO 32 (PWM soft start) |
| HC-SR04 TRIG / ECHO | GPIO 5 / 18 (echo via divider) |
| Battery sense | GPIO 34 via 100 kΩ / 22 kΩ divider |
| Control | Bluetooth Classic serial from a phone app |
Firmware outline
- Pair with the phone; parse commands F, B, L, R, S, blade on/off.
- Ramp drive PWM to avoid jerks; soft-start the blade over 1 s.
- If ultrasonic < 30 cm, stop driving and the blade.
- If no command for 1 s (connection lost), stop everything.
- Cut off at 9.9 V pack voltage (3.3 V per cell) to protect the cells.
Test plan
| Test | Expected result |
|---|---|
| Lost connection | Blade stops within 2 s |
| Obstacle ahead | Stops at 30 cm |
| Full charge on grass | Run time and area |
| Solar charge from empty | Hours to full |
These rows start your results table when you plan the project.
Viva practice
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 5.
Make it yours
One or two upgrades for a mini project, two to four for a major one.
Datasheets and sources to cite
- Johnson geared motor datasheet
- IS 14148 / ISO 5395 (lawnmower safety)
- MNRE off-grid solar guidelines
About this project
How much does the solar-powered grass cutter with remote control project cost?
About ₹6,045 for the parts in the base list: ESP32 DevKit V1, Solar panel 12 V 10 W, CN3791 MPPT solar Li-ion charger (3S setting), Li-ion 18650 pack 3S2P (11.1 V), 3S BMS 20 A, Johnson geared motor 300 RPM 12 V × 2, L298N motor driver, 775 DC motor 12 V with blade and guard, IRF3205 MOSFET, 1N5822 Schottky diode, HC-SR04 ultrasonic sensor, LM2596 buck converter, 5 A glass fuse with holder, Chassis, wheels and blade guard.
How long does it take?
About 10 weeks for the base project, built on an ESP32. Each upgrade adds time.
Which branches is it suitable for?
Mechanical / Mechatronics, Electrical and Electronics, Diploma (any electronics branch), as a mini or major project.
Which pins and design calculations does it use?
L298N ENA, IN1, IN2, IN3, IN4, ENB on GPIO 25, 26, 27, 14, 12, 33; Blade MOSFET gate (via 100 Ω, 10 kΩ pull-down) on GPIO 32 (PWM soft start); HC-SR04 TRIG / ECHO on GPIO 5 / 18 (echo via divider). Worked calculations on this page: blade motor energy, run time, solar charge time, area per charge, blade tip speed.
How do I test it?
Lost connection: Blade stops within 2 s. Obstacle ahead: Stops at 30 cm. Full charge on grass: Run time and area. Solar charge from empty: Hours to full.
What are the objectives?
To drive the cutter from a phone over Bluetooth. To cut grass with a guarded blade that stops in under 2 s when commanded or on an obstacle. To charge the pack from the solar panel and measure charge time. To measure area cut per charge and cost per year against a petrol mower.
