Projects / Soil probe powered only when reading

Soil probe powered only when reading

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Wire the probe

    VCC to D7, GND to GND, AO to A0.

  2. NANO14.9 mASSD1306

    Wire the OLED

    SDA to A4, SCL to A5, power from 5V and GND.

  3. NANO14.9 mASSD1306

    Install the libraries

    Adafruit SSD1306 and Adafruit GFX.

  4. NANO

    Calibrate dry

    Probe in air, note the raw value.

  5. NANO

    Calibrate wet

    Prongs in water, note the raw value.

  6. NANO

    Enter the values

    Put them in DRY_RAW and WET_RAW.

  7. NANOYL69soil 49%

    Push the prongs into the soil

    Watch the percentage.

  8. NANO

    Water the pot

    The percentage rises within a minute.

In short

How do you build a soil probe powered only when reading?

A resistive soil probe corrodes fast if it is powered all the time, so a pin switches it on only for a quick reading. You need Arduino Nano, Soil moisture sensor (resistive, YL-69), SSD1306 OLED Display, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 8 steps and about 75 minutes.

Level
Beginner
Time
About 75 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Soil module VCCNano D7Power only while measuring
Soil module GNDNano GNDCommon ground
Soil module AONano A0Analog moisture value
OLED VCC and GNDNano 5V and GNDPower
OLED SDANano A4I2C data
OLED SCLNano A5I2C clock

Code

A resistive soil probe measures moisture by passing a small current between two metal prongs through the soil. If that current flows all day, electrolysis eats the prongs and the readings drift within weeks. The fix is simple: power the module from an output pin instead of from 5 volts, switch it on only for a short reading, and switch it off again. The Nano pin can safely supply a module of this kind, which draws only some milliamps. The sketch turns the probe on, waits 200 milliseconds for the reading to settle, averages eight samples, and turns it off, so the prongs are powered for well under a second out of every ten. On this probe a lower raw number means wetter soil. Measure the probe in dry air and in a glass of water, write those two numbers into DRY_RAW and WET_RAW, and the percentage then makes sense for your probe. Readings still depend on the soil type, how tightly it is packed and the temperature, so treat the percentage as a guide rather than an exact measure. Keep the electronics board and the OLED dry and push only the prongs into the pot. For a week long test, power a spare probe in a second pot all the time and compare how the two prongs look afterwards.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

Adafruit_SSD1306 oled(128, 64, &Wire, -1);
const int PROBE_POWER = 7, PROBE_PIN = A0;
const int DRY_RAW = 950;                    // reading with the probe in dry air, measure yours
const int WET_RAW = 400;                    // reading with the prongs in a glass of water
const unsigned long EVERY = 10000;          // one reading every 10 seconds
unsigned long last = 0;

int readProbe() {
  digitalWrite(PROBE_POWER, HIGH);          // power the probe
  delay(200);                               // let the reading settle
  long sum = 0;
  for (int i = 0; i < 8; i++) { sum += analogRead(PROBE_PIN); delay(5); }
  digitalWrite(PROBE_POWER, LOW);           // and switch it off again
  return sum / 8;
}

void setup() {
  pinMode(PROBE_POWER, OUTPUT);
  digitalWrite(PROBE_POWER, LOW);
  Serial.begin(9600);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);   // try 0x3D if the screen stays blank
  oled.clearDisplay(); oled.display();
  last = millis() - EVERY;                  // read at once
}

void loop() {
  if (millis() - last >= EVERY) {
    last = millis();
    int raw = readProbe();
    int pct = constrain(map(raw, DRY_RAW, WET_RAW, 0, 100), 0, 100);

    oled.clearDisplay();
    oled.setTextColor(SSD1306_WHITE);
    oled.setTextSize(2);
    oled.setCursor(0, 4);  oled.print("Soil ");  oled.print(pct); oled.print("%");
    oled.setTextSize(1);
    oled.setCursor(0, 40); oled.print("Raw: "); oled.print(raw);
    oled.display();

    Serial.print(millis() / 1000); Serial.print(" s, raw "); Serial.print(raw);
    Serial.print(", "); Serial.print(pct); Serial.println(" %");
  }
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

0 s, raw 512, 79 %

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe in dry airAbout 0 percent
Prongs in waterAbout 100 percent
Damp soilSomewhere in between
Between readingsProbe is unpowered
Water the potPercentage climbs on the next readings

If it does not work

Screen blank

Try address 0x3D and check SDA and SCL.

Reading never changes

Check AO is on A0 and the probe is powered from D7.

Percentage backwards

Swap DRY_RAW and WET_RAW values you measured.

Readings jump

Increase the delay before reading or press the prongs deeper.

Probe is green or crusty

It was powered too long, replace it and keep the on-demand power.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the soil probe powered only when reading?

Arduino Nano, Soil moisture sensor (resistive, YL-69), SSD1306 OLED Display, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the soil probe powered only when reading take to build?

About 75 minutes for a beginner maker, in 8 steps.

How do I know the soil probe powered only when reading works?

Probe in dry air: About 0 percent. Prongs in water: About 100 percent. Damp soil: Somewhere in between.

Screen blank: what should I check?

Try address 0x3D and check SDA and SCL.

Reading never changes: what should I check?

Check AO is on A0 and the probe is powered from D7.

Percentage backwards: what should I check?

Swap DRY_RAW and WET_RAW values you measured.

Readings jump: what should I check?

Increase the delay before reading or press the prongs deeper.