Projects / Spinning ring stopwatch

Spinning ring stopwatch

A sixteen-LED ring sweeps like a clock hand to show seconds, with start and stop buttons.

Beginner1.3 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Install the library

    Add Adafruit NeoPixel.

  2. NANO12.8 mA

    Wire the ring

    5V, GND and DIN through a 330 ohm resistor to D6.

  3. NANO12.9 mA

    Add the capacitor

    100 uF across the ring supply.

  4. NANO

    Wire the buttons

    D2 and D3 each to GND.

  5. NANO12.9 mA

    Upload the sketch

    The ring stays dark.

  6. NANO12.9 mA

    Press start

    LEDs fill one per second.

  7. NANO

    Press lap

    White flash and a line in the serial monitor.

  8. NANO

    Stop and reset

    Press start, then the lap button.

In short

How do you build a spinning ring stopwatch?

A sixteen-LED ring sweeps like a clock hand to show seconds, with start and stop buttons. You need Arduino Nano, WS2812B ring 16 LEDs, Tactile push button 6 mm × 2, Resistor 330 Ω, Electrolytic Capacitor 100 µF and Breadboard 830 Tie Points. It takes 8 steps and about 75 minutes.

Level
Beginner
Time
About 75 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Ring 5VNano 5VKeep brightness low in code
Ring GNDNano GNDCommon ground
Ring DIN330 ohmThen to Nano D6
100 uF capacitorRing 5V to GNDLong leg to 5V
Start and stop buttonNano D2 to GNDUses the internal pull-up
Lap and reset buttonNano D3 to GNDUses the internal pull-up

Code

A WS2812B ring holds sixteen RGB LEDs on a single data wire, so one Nano pin controls the whole ring. This stopwatch lights one more LED each second, so a full turn of the ring is sixteen seconds, and every turn uses a new colour so you can count turns at a glance. The bright white head LED works like a clock hand. The start and stop button runs and pauses the count. While it is running, the lap button prints the lap time to the serial monitor and flashes the ring white. When it is stopped, the same button resets to zero. The buttons use the internal pull-up resistors, so no extra parts are needed. A small resistor on the data line and a capacitor across the ring supply protect the first LED from surges. Keep the brightness low: all sixteen LEDs at full white can draw close to one amp, more than a USB port on a laptop should give, and low brightness also looks nicer in a dim room. The timing uses the board clock, which drifts by a second or so a day, so this is for fun and lap timing, not for precise timekeeping.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Adafruit_NeoPixel.h>

const int RING_PIN = 6, N = 16, START_BTN = 2, LAP_BTN = 3;
Adafruit_NeoPixel ring(N, RING_PIN, NEO_GRB + NEO_KHZ800);

bool running = false;
unsigned long elapsed = 0, lastTick = 0;
unsigned long lastPress = 0;
int lap = 0;

bool clicked(int pin) {
  if (digitalRead(pin) == LOW && millis() - lastPress > 250) {
    lastPress = millis();
    return true;
  }
  return false;
}

uint32_t lapColour(int l) {
  uint32_t c[] = {ring.Color(0, 0, 60), ring.Color(0, 60, 0), ring.Color(60, 30, 0), ring.Color(60, 0, 40)};
  return c[l % 4];
}

void show() {
  ring.clear();
  int pos = (elapsed / 1000) % N;                    // one LED per second, one lap every 16 seconds
  int laps = (elapsed / 1000) / N;
  for (int i = 0; i <= pos; i++) ring.setPixelColor(i, lapColour(laps));
  ring.setPixelColor(pos, ring.Color(70, 70, 70));   // bright head
  ring.show();
}

void printTime() {
  unsigned long s = elapsed / 1000, tenths = (elapsed / 100) % 10;
  Serial.print(s / 60); Serial.print(":");
  if (s % 60 < 10) Serial.print("0");
  Serial.print(s % 60); Serial.print("."); Serial.println(tenths);
}

void setup() {
  pinMode(START_BTN, INPUT_PULLUP);
  pinMode(LAP_BTN, INPUT_PULLUP);
  ring.begin();
  ring.setBrightness(40);
  ring.show();
  Serial.begin(9600);
}

void loop() {
  unsigned long now = millis();
  if (running) { elapsed += now - lastTick; }
  lastTick = now;

  if (clicked(START_BTN)) running = !running;
  if (clicked(LAP_BTN)) {
    if (running) {
      lap++;
      Serial.print("Lap "); Serial.print(lap); Serial.print(": "); printTime();
      for (int i = 0; i < N; i++) ring.setPixelColor(i, ring.Color(70, 70, 70));
      ring.show();
      delay(120);
    } else {
      elapsed = 0; lap = 0;                          // reset when stopped
      Serial.println("Reset");
    }
  }
  show();
  delay(20);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press startRing fills one LED per second
Sixteen secondsRing restarts in a new colour
Lap press while runningRing flashes and a lap is printed
Stop then lap pressBack to zero
Press start againCounts from the stopped time

If it does not work

Ring stays dark

Check the DIN direction on the ring and the pin number.

Wrong colours

Change NEO_GRB to NEO_RGB.

Flickering LEDs

Add the 100 uF capacitor and a common ground.

Buttons act twice

Increase the 250 ms debounce time.

Nano resets

Lower the brightness value.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the spinning ring stopwatch?

Arduino Nano, WS2812B ring 16 LEDs, Tactile push button 6 mm × 2, Resistor 330 Ω, Electrolytic Capacitor 100 µF and Breadboard 830 Tie Points.

How long does the spinning ring stopwatch take to build?

About 75 minutes for a beginner maker, in 8 steps.

How do I know the spinning ring stopwatch works?

Press start: Ring fills one LED per second. Sixteen seconds: Ring restarts in a new colour. Lap press while running: Ring flashes and a lap is printed.

Ring stays dark: what should I check?

Check the DIN direction on the ring and the pin number.

Wrong colours: what should I check?

Change NEO_GRB to NEO_RGB.

Flickering LEDs: what should I check?

Add the 100 uF capacitor and a common ground.

Buttons act twice: what should I check?

Increase the 250 ms debounce time.