Wien bridge sine oscillator
Build it step by step
0 of 8 doneCheck the supply
Measure +V, 0 V and -V from the dual-rail module before connecting the chip.
Build the Wien network
R1 with C1 in series from the output to pin 3, R2 with C2 in parallel from pin 3 to ground.
Build the gain network
Rg from pin 2 to ground, Rf1 plus the pot from the output to pin 2.
Set the gain high
Start with the pot at the end that gives the larger resistance so the oscillation starts.
Look at the output
A scope or a sound card scope program should show a sine near 1.6 kHz.
Reduce the gain until it is clean
Turn the pot slowly until the top of the wave is round, not flat.
Remove the diodes
Take them out and see the amplitude grow until it clips, then put them back.
Change R
Try two 4.7 kΩ resistors in place of the 10 kΩ and see the frequency rise.
How do you build a wien bridge sine oscillator?
An op-amp and an RC network make a clean sine wave at about 1.6 kHz, with diodes to control the gain. You need TL072 dual JFET op-amp, Resistor 10 kΩ × 3, Resistor 4.7 kΩ, Ceramic capacitor 10 nF × 2, Signal Diode 1N4148 × 2, Potentiometer 10 kΩ, Dual-rail ±12 V DC-DC module, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 120 minutes.
- Level
- Intermediate
- Time
- About 120 min
- Parts
- 9
Parts list
- Integrated CircuitsBuy
- PassivesBuyResistor 10 kΩ × 3
- PassivesBuyResistor 4.7 kΩ × 1
- PassivesBuy
- SemiconductorsBuy
- PassivesBuy
- Power
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Dual-rail module + rail | TL072 pin 8 (V+) | Positive supply |
| Dual-rail module - rail | TL072 pin 4 (V-) | Negative supply |
| Dual-rail module 0 V | Breadboard ground rail | Signal ground |
| 10 kΩ resistor (R1) and 10 nF capacitor (C1) in series | TL072 pin 1 (OUT) to TL072 pin 3 (IN+A) | Series arm of the Wien network |
| 10 kΩ resistor (R2) and 10 nF capacitor (C2) in parallel | TL072 pin 3 to ground | Parallel arm of the Wien network |
| 4.7 kΩ resistor (Rg) | TL072 pin 2 (IN-A) to ground | Gain setting, bottom |
| 10 kΩ resistor (Rf1) | TL072 pin 1 to a junction X | Gain setting, top, first part |
| 10 kΩ potentiometer (Rf2) | Junction X to TL072 pin 2 | Gain trim, use the wiper and one end |
| 1N4148 diodes (two) | Anti-parallel across Rf1, cathode to anode | Limits the amplitude |
| TL072 pin 1 | Scope or sound card input | Sine output |
No code needed
No code. The oscillation frequency is f = 1 ÷ (2π R C): with R = 10 kΩ and C = 10 nF this is about 1.6 kHz. For exactly 1 kHz use 16 nF (for example 10 nF and 6.8 nF in parallel). The Wien network passes one third of the signal at that frequency, so the amplifier needs a gain of just over 3. Gain is 1 + (Rf1 + Rf2) ÷ Rg, which runs from about 3.1 to 5.3 with these parts. Too little gain and the circuit never starts, too much and the sine clips. The two diodes shunt Rf1 when the amplitude gets large, which lowers the gain and settles the amplitude. Use a small signal level and keep the output off headphones or speakers.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Frequency with 10 kΩ and 10 nF | About 1.6 kHz |
| Pot at the lowest gain | Oscillation stops or is very small |
| Pot at the highest gain without diodes | Clipped output |
| With diodes | Steady amplitude of a few volts peak |
If it does not work
No output
Increase the gain setting; check pins 8 and 4 have power.
Clipped output
Reduce the gain or check the diodes are fitted both ways round.
Wrong frequency
Check R1, R2, C1 and C2 values and that the series and parallel arms are in the right places.
Hum or noise
Add a 100 nF capacitor from each supply pin to ground and keep leads short.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the wien bridge sine oscillator?
TL072 dual JFET op-amp, Resistor 10 kΩ × 3, Resistor 4.7 kΩ, Ceramic capacitor 10 nF × 2, Signal Diode 1N4148 × 2, Potentiometer 10 kΩ, Dual-rail ±12 V DC-DC module, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).
How long does the wien bridge sine oscillator take to build?
About 120 minutes for a intermediate maker, in 8 steps.
How do I know the wien bridge sine oscillator works?
Frequency with 10 kΩ and 10 nF: About 1.6 kHz. Pot at the lowest gain: Oscillation stops or is very small. Pot at the highest gain without diodes: Clipped output.
No output: what should I check?
Increase the gain setting; check pins 8 and 4 have power.
Clipped output: what should I check?
Reduce the gain or check the diodes are fitted both ways round.
Wrong frequency: what should I check?
Check R1, R2, C1 and C2 values and that the series and parallel arms are in the right places.
Hum or noise: what should I check?
Add a 100 nF capacitor from each supply pin to ground and keep leads short.
