Projects / Whack-a-mole arcade game

Whack-a-mole arcade game

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO20.0 mA

    Test each button and LED

    Light each LED when its button is pressed.

  2. NANO12:45

    Show the score

    Count up on the TM1637.

  3. NANO20.0 mA

    Add the random mole

    Light one button at a time.

  4. NANO

    Add the timer

    Shrinking window.

  5. NANO

    Add sounds

    Hit and miss tracks.

  6. NANO8.0 mA

    Add game over

    Flash all buttons after three misses.

  7. NANO

    Build the box

    Five holes and a display window.

In short

How do you build a whack-a-mole arcade game?

Five lit arcade buttons pop on at random and you hit them before they go out, faster each round. You need Arduino Nano, Push button 16 mm metal (momentary, LED) × 5, TM1637 4-digit display, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10) and Resistor 1 kΩ. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Button LEDsNano D2 to D6, each through 220 ΩLight each button
ButtonsNano A0 to A4 to ground (internal pull-ups)Hit inputs
TM1637 CLK and DIONano D7 and D8Score display
DFPlayer RXNano D11 through 1 kΩSound commands
DFPlayer TXNano D10Status
DFPlayer SPK pins8 Ω speakerSound
All VCC and GNDNano 5V and GNDPower from USB

Code

Each round lights one random button and gives you a shrinking window to press it; hits shorten the window by 40 ms down to a floor of 350 ms, and three misses end the game. Put two short sounds on the DFPlayer's microSD card named 0001.mp3 for a hit and 0002.mp3 for a miss. The 1 kΩ in the DFPlayer RX line stops the Nano's 5 V signal from overdriving it. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails). Keep the sound at a comfortable level for children, and use a box with rounded corners.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Whack-a-mole: hit the lit button before time runs out. Libraries: TM1637Display, DFRobotDFPlayerMini.
#include <TM1637Display.h>
#include <SoftwareSerial.h>
#include <DFRobotDFPlayerMini.h>
const int LED[5] = {2, 3, 4, 5, 6};
const int BTN[5] = {A0, A1, A2, A3, A4};
TM1637Display disp(7, 8);
SoftwareSerial sw(10, 11);
DFRobotDFPlayerMini dfp;
int score = 0, misses = 0, window = 1500;
void setup() {
  for (int i = 0; i < 5; i++) { pinMode(LED[i], OUTPUT); pinMode(BTN[i], INPUT_PULLUP); }
  disp.setBrightness(5);
  sw.begin(9600);
  if (dfp.begin(sw)) dfp.volume(15);
  randomSeed(analogRead(A5));
  disp.showNumberDec(0);
}
void loop() {
  int m = random(5);
  digitalWrite(LED[m], HIGH);
  unsigned long start = millis();
  bool hit = false;
  while (millis() - start < (unsigned long)window) {
    if (digitalRead(BTN[m]) == LOW) { hit = true; break; }
  }
  digitalWrite(LED[m], LOW);
  if (hit) { score++; window = max(350, window - 40); dfp.play(1); }
  else { misses++; dfp.play(2); }
  disp.showNumberDec(score);
  if (misses >= 3) {                              // game over: flash every button
    for (int k = 0; k < 4; k++) {
      for (int i = 0; i < 5; i++) digitalWrite(LED[i], HIGH);
      delay(250);
      for (int i = 0; i < 5; i++) digitalWrite(LED[i], LOW);
      delay(250);
    }
    score = 0; misses = 0; window = 1500; disp.showNumberDec(0);
  }
  delay(random(300, 900));
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hit in timeScore goes up and the window shortens
MissMiss sound plays
Three missesAll buttons flash and the game resets
SoundClear and not too loud

If it does not work

No sound

Check the file names on the card and the RX resistor.

Buttons stuck

Check the ground wires.

Display blank

Check CLK and DIO order.

Game too fast

Raise the starting window.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the whack-a-mole arcade game?

Arduino Nano, Push button 16 mm metal (momentary, LED) × 5, TM1637 4-digit display, DFPlayer Mini MP3 module, Speaker 8 Ω 0.5 W, SanDisk microSD card 32 GB (A1, Class 10) and Resistor 1 kΩ. Push button 16 mm metal (momentary, LED) × 5: Arcade LED buttons work too.

How long does the whack-a-mole arcade game take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the whack-a-mole arcade game works?

Hit in time: Score goes up and the window shortens. Miss: Miss sound plays. Three misses: All buttons flash and the game resets.

No sound: what should I check?

Check the file names on the card and the RX resistor.

Buttons stuck: what should I check?

Check the ground wires.

Display blank: what should I check?

Check CLK and DIO order.

Game too fast: what should I check?

Raise the starting window.