Projects / Servo needle voltmeter

Servo needle voltmeter

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANOVOLTAGE4.70 V

    Wire the module

    Connect the signal side to A0 and ground, and the input to the voltage to measure.

  2. NANOVOLTAGE4.70 V

    Read the voltage

    Open the Serial Monitor and compare with a multimeter on a 9 V battery.

  3. NANO

    Set the calibration

    Adjust CAL until the two match.

  4. NANO59°

    Wire the servo

    Add the capacitor and check the needle moves.

  5. NANO

    Print the dial

    Draw a 0 to 15 V arc on card with ticks every volt, mounted behind the needle.

  6. NANO

    Calibrate the marks

    Test at 3 V, 6 V, 9 V and 12 V and re-mark the dial if needed.

In short

How do you build a servo needle voltmeter?

A servo needle on a printed dial shows a voltage like an old analogue meter. You need Arduino Nano, SG90 Micro Servo, Voltage sensor module (0 to 25 V), Electrolytic capacitor 1000 µF and Breadboard 830 Tie Points. It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Voltage module VCC pin (signal side)Left unconnectedThe module does not need it
Voltage module S (signal)Nano A0Reduced voltage, one fifth of the input
Voltage module - (signal side)Nano GNDCommon ground
Voltage module input VCC+ and GNDVoltage to measure, 0 to 15 V only hereInput terminals
Servo signalNano D9Needle
Servo redNano 5V pin or a separate 5 V supplyPower
Servo brownNano GNDGround
1000 µF capacitorAcross the servo power wires, + to 5 VAbsorbs servo surges

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). No libraries needed beyond the built-in Servo. The 0 to 25 V sensor module divides the input by five, so A0 sees at most 5 V. Measure DC only, up to 15 V in this build (so the dial uses most of the servo's travel); never measure mains. Set CAL by comparing the Serial reading with a multimeter. Keep the servo's power wires short and use the capacitor, or power it from a separate 5 V supply with a common ground, so the needle does not twitch.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Servo.h>

Servo needle;
const byte SENSE = A0;
const float FULL_SCALE_V = 15.0;           // voltage at the right-hand end of the dial
float CAL = 5.0;                           // module divider ratio; adjust against a multimeter
float shown = 0;

void setup() {
  Serial.begin(9600);
  needle.attach(9);
}

void loop() {
  long s = 0;
  for (byte i = 0; i < 16; i++) s += analogRead(SENSE);
  float volts = (s / 16.0) * 5.0 / 1023.0 * CAL;
  shown = 0.9 * shown + 0.1 * volts;       // smoothing makes the needle glide
  int angle = constrain(map((long)(shown * 100), 0, (long)(FULL_SCALE_V * 100), 20, 160), 20, 160);
  needle.write(angle);
  Serial.println(shown, 2);
  delay(30);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

0.50
0.95
1.36
1.72
2.05
2.35

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
0 VNeedle at the left end
7.5 VNeedle in the middle
15 VNeedle at the right end
Changing voltageNeedle glides smoothly

If it does not work

Needle twitches

Add the capacitor or power the servo separately.

Reading wrong

Set CAL against a multimeter and check the module's signal pin.

Needle at the end stop

The voltage is above FULL_SCALE_V. Lower the input.

Reading never changes

Check the ground link between the module and the Nano.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the servo needle voltmeter?

Arduino Nano, SG90 Micro Servo, Voltage sensor module (0 to 25 V), Electrolytic capacitor 1000 µF and Breadboard 830 Tie Points.

How long does the servo needle voltmeter take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the servo needle voltmeter works?

0 V: Needle at the left end. 7.5 V: Needle in the middle. 15 V: Needle at the right end.

Needle twitches: what should I check?

Add the capacitor or power the servo separately.

Reading wrong: what should I check?

Set CAL against a multimeter and check the module's signal pin.

Needle at the end stop: what should I check?

The voltage is above FULL_SCALE_V. Lower the input.

Reading never changes: what should I check?

Check the ground link between the module and the Nano.