Projects / Voice memo recorder

Voice memo recorder

Beginner30 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. Wire the power

    Two AA cells to VCC and GND.

  2. Connect the speaker

    8 Ω speaker to SP+ and SP-.

  3. Record

    Hold REC, speak into the microphone for up to 10 seconds, then release.

  4. Play back

    Press PLAYE and hear the message once. PLAYL plays while held.

  5. Add your own buttons

    Wire a push button from VCC to REC and another from VCC to PLAYE if you want a bigger control.

  6. Change the length

    Check the resistor table in the module's guide and swap the sample-rate resistor.

  7. Trigger it

    A PIR sensor output to PLAYE makes a greeting that plays when someone walks by.

In short

How do you build a voice memo recorder?

An ISD1820 module records a 10-second message at the press of a button and plays it back. You need ISD1820 voice recorder module, Speaker 8 Ω 0.5 W, Tactile push button 6 mm × 2, Battery holder 2 × AA, AA alkaline battery × 2 and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Battery holder +Module VCC3 V from 2 AA cells (the chip works from 2.4 to 5.5 V)
Battery holder -Module GNDGround
SpeakerModule SP+ and SP-Playback
REC button (optional extra)Module VCC to REC pinHold to record
PLAYE button (optional extra)Module VCC to PLAYE pinTap to play once

No code needed

No code. The module has its own REC, PLAYE and PLAYL buttons and a built-in microphone, so the external buttons are optional. Do not power it from four fresh AA cells, which gives about 6.4 V and exceeds its limit. Recording time is about 10 seconds by default and can be changed with the resistor on the board.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hold REC and speakRecording LED lit
Press PLAYEMessage plays once
Record againThe old message is overwritten
Power off and onRecording is still there

If it does not work

Quiet playback

Speaker too small or battery weak. Use fresh cells.

Distorted voice

Too close to the microphone. Speak from 20 cm.

Nothing plays

Message was not recorded. Hold REC the whole time.

Module gets hot

Voltage too high. Use 3 V.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the voice memo recorder?

ISD1820 voice recorder module, Speaker 8 Ω 0.5 W, Tactile push button 6 mm × 2, Battery holder 2 × AA, AA alkaline battery × 2 and Jumper wires male to male (40 pcs, 20 cm).

How long does the voice memo recorder take to build?

About 30 minutes for a beginner maker, in 7 steps.

How do I know the voice memo recorder works?

Hold REC and speak: Recording LED lit. Press PLAYE: Message plays once. Record again: The old message is overwritten.

Quiet playback: what should I check?

Speaker too small or battery weak. Use fresh cells.

Distorted voice: what should I check?

Too close to the microphone. Speak from 20 cm.

Nothing plays: what should I check?

Message was not recorded. Hold REC the whole time.

Module gets hot: what should I check?

Voltage too high. Use 3 V.