Projects / UV index meter for the terrace

UV index meter for the terrace

Beginner1 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire the sensor

    Connect VCC, GND and OUT to 5V, GND and A0. Keep the sensor's window facing the sky.

  2. NANO15.6 mA

    Wire the LED

    Put a 220 Ω resistor in series with each colour leg and join the common cathode to GND.

  3. NANO

    Wire the display

    CLK to D2, DIO to D3, power to 5V and GND.

  4. NANO

    Upload and look at the serial monitor

    Open the monitor at 9600 baud and note the millivolts indoors, which should be near zero.

  5. NANO

    Take it outside

    Point it at the sky around noon. The value should rise and the colour change.

  6. NANO

    Compare

    Check the reading against your city's UV forecast and scale the divisor if it is consistently off.

In short

How do you build an UV index meter for the terrace?

A GUVA-S12SD sensor estimates the UV index and colours an LED green, yellow, orange or red to say when to use sunscreen. You need Arduino Nano, GUVA-S12SD UV sensor module, RGB LED 5 mm common cathode, Resistor 220 Ω × 3, TM1637 4-digit display, 5 V 2 A USB adapter, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
GUVA module VCCNano 5VSensor supply
GUVA module GNDNano GNDCommon ground
GUVA module OUTNano A0Analog UV voltage
RGB LED red legNano D9 through a 220 Ω resistorRed channel
RGB LED green legNano D10 through a 220 Ω resistorGreen channel
RGB LED blue legNano D11 through a 220 Ω resistorBlue channel (unused, kept dark)
RGB LED common cathode (longest leg)Nano GNDCommon cathode type
TM1637 CLKNano D2Display clock
TM1637 DIONano D3Display data
TM1637 VCC and GNDNano 5V and GNDDisplay supply

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install the library "TM1637" by Avishay Orpaz from Library Manager. The display shows the index in tenths, so 25 means 2.5. The 100 mV per step figure is approximate and should be checked against your module's chart.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>

const byte SENSOR = A0;
const byte R = 9, G = 10;
TM1637Display display(2, 3);   // CLK, DIO

void setColour(byte r, byte g) { analogWrite(R, r); analogWrite(G, g); }

void setup() {
  pinMode(R, OUTPUT); pinMode(G, OUTPUT);
  display.setBrightness(5);
  Serial.begin(9600);
}

void loop() {
  long sum = 0;
  for (byte i = 0; i < 32; i++) { sum += analogRead(SENSOR); delay(5); }
  float mv = (sum / 32.0) * 5000.0 / 1023.0;      // millivolts at the pin
  float uvi = mv / 100.0;                          // about 100 mV per UV index step, see the module chart
  if (uvi < 0.3) uvi = 0;

  display.showNumberDec((int)(uvi * 10 + 0.5));   // tenths: 25 means UV index 2.5
  if (uvi < 3)       setColour(0, 200);           // low: green
  else if (uvi < 6)  setColour(200, 150);         // moderate: yellow
  else if (uvi < 8)  setColour(255, 50);          // high: orange
  else               setColour(255, 0);           // very high and above: red

  Serial.print(mv); Serial.print(" mV  UVI "); Serial.println(uvi);
  delay(500);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

2501.83 mV  UVI 25.02
2502.75 mV  UVI 25.03
2501.99 mV  UVI 25.02
2501.53 mV  UVI 25.02
2502.44 mV  UVI 25.02
2502.60 mV  UVI 25.03

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Cover the sensorThe display falls to 0 and the LED goes green
Torch with a UV LED or sunlight through a windowThe reading rises (ordinary white torches give almost nothing)
Midday sunOften 6 to 10 in summer in most of India, so orange or red
Compare with forecastWithin about 1 to 2 index points is reasonable for this sensor

If it does not work

Reading stays at zero outside

The sensor is behind glass, which blocks UV, or the OUT wire is not on A0.

Readings jump around

Average more samples and keep the sensor wires short.

Display is blank

Swap CLK and DIO, and check the 5 V supply.

LED shows the wrong colours

You have a common anode RGB LED. Join the long leg to 5V and invert the analogWrite values.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the UV index meter for the terrace?

Arduino Nano, GUVA-S12SD UV sensor module, RGB LED 5 mm common cathode, Resistor 220 Ω × 3, TM1637 4-digit display, 5 V 2 A USB adapter, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the UV index meter for the terrace take to build?

About 60 minutes for a beginner maker, in 6 steps.

How do I know the UV index meter for the terrace works?

Cover the sensor: The display falls to 0 and the LED goes green. Torch with a UV LED or sunlight through a window: The reading rises (ordinary white torches give almost nothing). Midday sun: Often 6 to 10 in summer in most of India, so orange or red.

Reading stays at zero outside: what should I check?

The sensor is behind glass, which blocks UV, or the OUT wire is not on A0.

Readings jump around: what should I check?

Average more samples and keep the sensor wires short.

Display is blank: what should I check?

Swap CLK and DIO, and check the 5 V supply.

LED shows the wrong colours: what should I check?

You have a common anode RGB LED. Join the long leg to 5V and invert the analogWrite values.