Projects / USB isolator for safe probing

USB isolator for safe probing

Intermediate30 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. UNOUSB

    Plug the isolator in

    Between laptop and board.

  2. UNO

    Power the board

    From its own adapter.

  3. UNO

    Check it enumerates

    The port appears.

  4. UNO

    Upload the test sketch

    Programming works.

  5. UNO

    Open the Serial Monitor

    Messages arrive.

  6. UNO

    Type some text

    It is echoed back.

  7. UNOUSB

    Remove the isolator and compare

    Note any change in noise.

In short

How do you build an USB isolator for safe probing?

Put an isolator between your laptop and a project so ground loops and faults cannot hurt the laptop. You need USB isolator (ADuM3160), Arduino Uno R3 and USB A to B cable (Uno / Mega). It takes 7 steps and about 30 minutes.

Level
Intermediate
Time
About 30 min
Parts
3

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Laptop USBIsolator input sideComputer side
Isolator output sideUno via the USB cableBoard side, data only
Uno powerIts own 7 to 12 V adapterThe board is powered separately
Uno pin 13Built-in LEDShows the program is running

Code

Normally a USB cable ties the grounds of your laptop and your project together. If the project touches a different ground, for example another supply or a measuring instrument, current can flow through the cable and the laptop's port, which adds noise or even damages the port. An isolator breaks that link: the data crosses over, and the ground does not. Plug it between the laptop and the board, give the board its own supply, and the ADuM3160 chip passes data at the full speed of USB 1.1 only, which is enough for serial and programming but not for fast transfers. Do not use it with mains-connected circuits or to connect to mains voltage; isolation here is for low-voltage lab work and does not make mains safe to touch. Probing with a scope is safest when the scope is also isolated or the project is battery-powered. If the board does not appear on the computer, check that the isolator is a data-only type and that the board has its own power. Arduino IDE, board "Arduino Uno".

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Isolated serial test: sends a message every second and echoes what you type. Board: Arduino Uno.
// If this works with the isolator in place, the data link is isolated from the laptop.
unsigned long last = 0;
int count = 0;
void setup() {
  Serial.begin(9600);
  pinMode(LED_BUILTIN, OUTPUT);
}
void loop() {
  if (millis() - last >= 1000) {
    last = millis();
    count++;
    digitalWrite(LED_BUILTIN, !digitalRead(LED_BUILTIN));
    Serial.print("isolated link alive, message "); Serial.println(count);
  }
  while (Serial.available()) Serial.write(Serial.read());    // echo whatever you type
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

isolated link alive, message 1
isolated link alive, message 2
isolated link alive, message 3
isolated link alive, message 4
isolated link alive, message 5
isolated link alive, message 6

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Isolator plugged inBoard appears as a port
Test sketchMessage every second
Type textEchoed back
Board unpoweredNo port, as expected

If it does not work

Board not found

Power the board separately and re-plug the isolator.

Upload fails

Slow baud rate; try another USB port.

Messages garbled

Check the baud rate is 9600.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the USB isolator for safe probing?

USB isolator (ADuM3160), Arduino Uno R3 and USB A to B cable (Uno / Mega).

How long does the USB isolator for safe probing take to build?

About 30 minutes for a intermediate maker, in 7 steps.

How do I know the USB isolator for safe probing works?

Isolator plugged in: Board appears as a port. Test sketch: Message every second. Type text: Echoed back.

Board not found: what should I check?

Power the board separately and re-plug the isolator.

Upload fails: what should I check?

Slow baud rate; try another USB port.

Messages garbled: what should I check?

Check the baud rate is 9600.