Projects / Tap water turbidity checker

Tap water turbidity checker

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire and read

    Connect the module and watch the voltage on the Serial Monitor.

  2. NANO

    Measure clear water

    Put the probe in a glass of bottled water and note the voltage.

  3. NANO

    Measure cloudy water

    Add a pinch of clay to a second glass and note it again.

  4. NANO

    Measure muddy water

    Add more clay and note it.

  5. NANO

    Set the thresholds

    Put values between your three readings into the code.

  6. NANO

    Test samples

    Check tap and stored water and compare with how they look.

In short

How do you build a tap water turbidity checker?

A turbidity sensor shines light through a sample and tells clear, slightly cloudy and muddy water apart. It does not say whether water is safe to drink. You need Arduino Nano, Turbidity sensor module and SSD1306 OLED Display. It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
3

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Turbidity module VCC, GNDNano 5V, GNDPower
Turbidity module signal (A)Nano A0Analog output
OLED SDA, SCLNano A4, A5I2C
OLED VCC, GNDNano 5V, GNDPower

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "U8g2". A higher voltage means clearer water for most turbidity modules. Only the probe end goes in water; keep the electronics box dry. Use the same glass, depth and lighting for every test, and rinse the probe after each sample. Clear water can still contain germs and chemicals: this tells you only how cloudy it is, so never use it to judge whether water is safe to drink.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <U8x8lib.h>

U8X8_SSD1306_128X64_NONAME_HW_I2C oled(U8X8_PIN_NONE);
const byte SENSOR = A0;
// Edit these after you have measured your own reference glasses (volts):
const float CLEAR_V = 4.0;                  // above this reads Clear
const float CLOUDY_V = 3.3;                 // above this reads Slightly cloudy, below it Muddy

void setup() {
  Serial.begin(9600);
  oled.begin();
  oled.setFont(u8x8_font_chroma48medium8_r);
}

void loop() {
  long s = 0;
  for (byte i = 0; i < 32; i++) { s += analogRead(SENSOR); delay(5); }
  float v = (s / 32.0) * 5.0 / 1023.0;
  Serial.println(v, 2);
  const char* label = v > CLEAR_V ? "Clear         " : (v > CLOUDY_V ? "Slightly cloudy" : "Muddy         ");
  char b[17], t[8];
  dtostrf(v, 4, 2, t); snprintf(b, sizeof b, "Sensor %s V", t);
  oled.drawString(0, 1, b);
  oled.drawString(0, 4, label);
  oled.drawString(0, 7, "Not a safety test");
  delay(500);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

2.50

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Bottled waterClear
Light clay in waterSlightly cloudy
Heavy clayMuddy
Probe in airA different, fixed reading; not meaningful

If it does not work

Reading always the same

Check the signal wire and that the probe is in water.

Values drift

Keep the same depth and let it settle for a few seconds.

Thresholds do not match

Re-measure your own glasses and edit the constants.

Screen blank

Check the I2C connection.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the tap water turbidity checker?

Arduino Nano, Turbidity sensor module and SSD1306 OLED Display.

How long does the tap water turbidity checker take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the tap water turbidity checker works?

Bottled water: Clear. Light clay in water: Slightly cloudy. Heavy clay: Muddy.

Reading always the same: what should I check?

Check the signal wire and that the probe is in water.

Values drift: what should I check?

Keep the same depth and let it settle for a few seconds.

Thresholds do not match: what should I check?

Re-measure your own glasses and edit the constants.

Screen blank: what should I check?

Check the I2C connection.