Thermistor bridge temperature alarm
Build it step by step
0 of 6 doneBuild the bridge
Wire the NTC and the 10 kΩ resistor as a divider and read node A with a multimeter at room temperature.
Set the reference
Turn the potentiometer until its wiper voltage is just above node A.
Add the comparator
Wire the LM393 with node A on pin 3 and the wiper on pin 2.
Add the buzzer driver
Fit the pull-up, base resistor, transistor and buzzer.
Test with warmth
Hold the thermistor between your fingers and slowly turn the pot down until the buzzer just sounds.
Add hysteresis
Fit the 100 kΩ resistor so the buzzer does not chatter at the trip point.
How do you build a thermistor bridge temperature alarm?
A thermistor in a bridge with a comparator sounds a buzzer when something gets too hot, with no microcontroller at all. You need NTC thermistor 10 kΩ (B3950), Resistor 10 kΩ × 3, Resistor 1 kΩ, Resistor 100 kΩ, Potentiometer 10 kΩ, LM393 Comparator, BC547 NPN transistor, Buzzer 12 V continuous (piezo alarm), Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 6 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 11
Parts list
- SensorsBuy
- PassivesBuyResistor 10 kΩ × 3
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuy
- Integrated CircuitsBuyLM393 Comparator × 1
- SemiconductorsBuy
- Motors & ActuatorsBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery snap + | Breadboard + rail | Supply |
| 9 V battery snap - | Breadboard - rail | Ground |
| LM393 pin 8 | + rail | Power |
| LM393 pin 4 | - rail | Ground |
| NTC thermistor | + rail and node A | Top of the sensing divider |
| 10 kΩ resistor | Node A and - rail | Bottom of the sensing divider |
| Node A | LM393 pin 3 (IN+) | Temperature voltage |
| Potentiometer outer pins | + rail and - rail | Reference divider |
| Potentiometer wiper | LM393 pin 2 (IN-) | Trip level |
| 10 kΩ resistor | LM393 pin 1 (OUT) and + rail | Pull-up for the open-collector output |
| 100 kΩ resistor | LM393 pin 1 (OUT) and pin 3 (IN+) | Hysteresis |
| 1 kΩ resistor | LM393 pin 1 (OUT) and BC547 base | Base resistor |
| BC547 emitter | - rail | Ground |
| BC547 collector | Buzzer - | Switches the buzzer |
| Buzzer + | + rail | Supply |
No code needed
No code. The NTC is on the top of the divider, so its resistance falls and node A rises as it heats. When node A goes above the potentiometer voltage the comparator output turns off, the pull-up takes the transistor base high and the buzzer sounds. Check that your 12 V piezo buzzer is rated to run at 9 V (most are rated 6 V or 3 V up to 15 V or more).
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Room temperature | Silent |
| Fingers on the thermistor | Buzzer sounds once the trip point is reached |
| Release and cool | Buzzer stops a little below the trip point (hysteresis) |
| Pot at the cold end | Buzzer on even at room temperature |
If it does not work
Buzzer always on
Pot wiper is below node A. Turn it up.
Buzzer never sounds
Check which way the pot turns and that the NTC is on the + side of the divider.
Buzzer chatters
The 100 kΩ hysteresis resistor is missing or on the wrong pin.
Buzzer quiet
The buzzer is too low in voltage rating. Use one rated for 9 V.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the thermistor bridge temperature alarm?
NTC thermistor 10 kΩ (B3950), Resistor 10 kΩ × 3, Resistor 1 kΩ, Resistor 100 kΩ, Potentiometer 10 kΩ, LM393 Comparator, BC547 NPN transistor, Buzzer 12 V continuous (piezo alarm), Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.
How long does the thermistor bridge temperature alarm take to build?
About 45 minutes for a beginner maker, in 6 steps.
How do I know the thermistor bridge temperature alarm works?
Room temperature: Silent. Fingers on the thermistor: Buzzer sounds once the trip point is reached. Release and cool: Buzzer stops a little below the trip point (hysteresis).
Buzzer always on: what should I check?
Pot wiper is below node A. Turn it up.
Buzzer never sounds: what should I check?
Check which way the pot turns and that the NTC is on the + side of the divider.
Buzzer chatters: what should I check?
The 100 kΩ hysteresis resistor is missing or on the wrong pin.
Buzzer quiet: what should I check?
The buzzer is too low in voltage rating. Use one rated for 9 V.
