Projects / Desktop stereo speakers with PAM8403

Desktop stereo speakers with PAM8403

Beginner2 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. USBUSB

    Power the module

    Connect the USB breakout and check the module's power LED.

  2. AUDIO

    Wire the volume

    Wire the dual pot between the jack and the module's inputs, with both wipers going to the amplifier.

  3. Connect one speaker

    Wire the left speaker to the L outputs only and test with a phone.

  4. Add the second

    Wire the right speaker and check stereo with a left-right test track.

  5. ABS

    Build the boxes

    Mount each speaker in a closed box, sealed with glue or foam gasket.

  6. Feel the chip

    After ten minutes at a loud volume, touch the module: it should be barely warm.

In short

How do you build a desktop stereo speakers with PAM8403?

A PAM8403 class-D board drives two 4 Ω speakers from 5 V USB, in a pair of small boxes with a shared volume knob. You need PAM8403 stereo amplifier module, Speaker 4 Ω 3 W × 2, Potentiometer 50 kΩ dual (stereo), Audio jack 3.5 mm (PCB, stereo), USB-A female breakout, USB A to micro-USB cable (data) and ABS project box (100 × 60 × 25 mm) × 2. It takes 6 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
USB breakout 5V and GNDPAM8403 module +5V and GNDPower
3.5 mm jack tip (left)Dual pot section 1 outer pinLeft signal in
3.5 mm jack ring (right)Dual pot section 2 outer pinRight signal in
3.5 mm jack sleeveDual pot other outer pins and module GNDSignal ground
Dual pot section 1 wiperPAM8403 L inputLeft volume
Dual pot section 2 wiperPAM8403 R inputRight volume
PAM8403 L+ and L- outputsLeft speakerNever connect either speaker lead to ground
PAM8403 R+ and R- outputsRight speakerSame, bridge-tied outputs

No code needed

No code. The PAM8403 outputs are bridge-tied, so each speaker connects between its two output pins and neither lead may touch ground or the other channel. A class-D amplifier switches its output transistors fully on or off at hundreds of kilohertz, so little power is wasted as heat: the chip stays cool even at loud volume, where a linear amplifier of the same output would run hot. Use a 5 V 1 A or larger USB supply; the amplifier can draw over 1 A on loud peaks. Use closed boxes for the speakers; open baffles lose bass.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Phone playing quietlyClear sound from both speakers
Knob turned downFades to silence
Left-right testEach side plays only its own channel
Loud volume for ten minutesChip stays cool

If it does not work

Hum or buzz

Share the signal ground and keep the signal wires short.

One channel silent

Check that speaker's connections and the pot section.

Sound distorts when loud

The USB supply is too small. Use a 5 V 2 A source.

Loud pop at switch-on

Turn the volume down before powering.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the desktop stereo speakers with PAM8403?

PAM8403 stereo amplifier module, Speaker 4 Ω 3 W × 2, Potentiometer 50 kΩ dual (stereo), Audio jack 3.5 mm (PCB, stereo), USB-A female breakout, USB A to micro-USB cable (data) and ABS project box (100 × 60 × 25 mm) × 2.

How long does the desktop stereo speakers with PAM8403 take to build?

About 120 minutes for a beginner maker, in 6 steps.

How do I know the desktop stereo speakers with PAM8403 works?

Phone playing quietly: Clear sound from both speakers. Knob turned down: Fades to silence. Left-right test: Each side plays only its own channel.

Hum or buzz: what should I check?

Share the signal ground and keep the signal wires short.

One channel silent: what should I check?

Check that speaker's connections and the pot section.

Sound distorts when loud: what should I check?

The USB supply is too small. Use a 5 V 2 A source.

Loud pop at switch-on: what should I check?

Turn the volume down before powering.